SNAA320B November   2019  – January 2024 LM4040-N , LM4050-N , LM4128 , LM4128-Q1 , LM4132 , LM4132-Q1 , REF102 , REF1925 , REF1930 , REF1933 , REF1941 , REF20-Q1 , REF200 , REF2025 , REF2030 , REF2033 , REF2041 , REF2125 , REF2912 , REF2920 , REF2925 , REF2930 , REF2933 , REF2940 , REF3012 , REF3020 , REF3025 , REF3030 , REF3033 , REF3033-Q1 , REF31-Q1 , REF3112 , REF3120 , REF3125 , REF3130 , REF3133 , REF3140 , REF3212 , REF3212-EP , REF3220 , REF3220-EP , REF3225 , REF3225-EP , REF3230 , REF3230-EP , REF3233 , REF3240 , REF3312 , REF3318 , REF3320 , REF3325 , REF3330 , REF3333 , REF34-Q1 , REF3425 , REF3425-EP , REF3430 , REF3430-EP , REF3433 , REF3433-EP , REF3440 , REF3440-EP , REF3450 , REF35 , REF4132 , REF4132-Q1 , REF5010 , REF5020 , REF5020-EP , REF5020A-Q1 , REF5025 , REF5025-EP , REF5025-HT , REF5025A-Q1 , REF5030 , REF5030A-Q1 , REF5040 , REF5040-EP , REF5040A-Q1 , REF5045 , REF5045A-Q1 , REF5050 , REF5050-EP , REF5050A-Q1 , REF54 , REF6125 , REF6133 , REF6141 , REF6145 , REF6150 , REF6225 , REF6230 , REF6233 , REF6241 , REF6245 , REF6250 , REF70 , TL431LI , TL432LI , TLV431

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Introduction
  5. 2 Analog-to-Digital Converter Error
  6. 3 Voltage Reference DC Error
    1. 3.1 Initial Accuracy and Solder Shift
    2. 3.2 Temperature Drift
    3. 3.3 Line Regulation
  7. 4 DC Error Calculations
  8. 5 Calibration
  9. 6 Voltage Reference Noise Error
    1. 6.1 1/f Noise
    2. 6.2 Broadband Noise
    3. 6.3 Power Supply Rejection Ratio
    4. 6.4 Noise Example
  10. 7 Dynamic Error (Voltage Reference Driving Capability)
  11. 8 Low Power Applications
  12. 9 References
  13. 10Revision History

6.2 Broadband Noise

Broadband noise is a flat noise that spans the complete frequency range of the device also known as wideband noise. Unlike 1/f noise, broadband noise affects the whole frequency range relatively equally; filtering out as much noise as possible is practical with either a RC filter or with digital filtering techniques. All circuits have broadband noise and a bandwidth limitation that limits the effect of the broadband noise so the noise is not infinite. Broadband noise is specified as either output noise from 10Hz to 10kHz or as output voltage noise density. Conversion between output noise outside and output noise density can be found in the precision labs noise series. One problem that a designer can run into is that noise is inversely proportional to quiescent current; therefore, achieving low noise in a low power system is difficult.