Widebus+ is a trademark of Texas Instruments.
This 25-bit 1:1 or 14-bit 1:2 configurable registered buffer is designed for 1.7-V to 1.9-V VCC operation. In the 1:1 pinout configuration, only one device per DIMM is required to drive nine SDRAM loads. In the 1:2 pinout configuration, two devices per DIMM are required to drive 18 SDRAM loads.
All inputs are SSTL_18, except the LVCMOS reset (RESET)\ and LVCMOS control (Cn) inputs. All outputs are edge-controlled circuits optimized for unterminated DIMM loads and meet SSTL_18 specifications.
The SN74SSTU32864 operates from a differential clock (CLK and CLK\). Data are registered at the crossing of CLK going high and CLK\ going low.
The C0 input controls the pinout configuration of the 1:2 pinout from register-A configuration (when low) to register-B configuration (when high). The C1 input controls the pinout configuration from 25-bit 1:1 (when low) to 14-bit 1:2 (when high). C0 and C1 should not be switched during normal operation. They should be hard-wired to a valid low or high level to configure the register in the desired mode. In the 25-bit 1:1 pinout configuration, the A6, D6, and H6 terminals are driven low and should not be used.
The device supports low-power standby operation. When RESET\ is low, the differential input receivers are disabled, and undriven (floating) data, clock, and reference voltage (VREF) inputs are allowed. In addition, when RESET\ is low, all registers are reset and all outputs are forced low. The LVCMOS RESET\ and Cn inputs always must be held at a valid logic high or low level.
The two VREF pins (A3 and T3), are connected together internally by approximately 150 
. However, it is necessary to connect only one of the two VREF pins to the external VREF power supply. An unused VREF pin should be terminated with a VREF coupling capacitor.
The device also supports low-power active operation by monitoring both system chip select (DCS\ and CSR\) inputs and will gate the Qn outputs from changing states when both DCS\ and CSR\ inputs are high. If either DCS\ or CSR\ input is low, the Qn outputs function normally. The RESET\ input has priority over the DCS\ and CSR\ control and forces the output low. If the DCS\ control functionality is not desired, the CSR\ input can be hard-wired to ground, in which case, the setup-time requirement for DCS\ is the same as for the other D data inputs.
To ensure defined outputs from the register before a stable clock has been supplied, RESET\ must be held in the low state during power up.
| Typ | Titel | Datum | ||
|---|---|---|---|---|
| * | Data sheet | SN74SSTU32864 datasheet | 20 Mär 2003 | |
| * | User guide | CTS MicroStar BGA Discontinued and Redesigned | 08 Mai 2022 | |
| Selection guide | Logic Guide (Rev. AB) | 12 Jun 2017 | ||
| Application note | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 02 Dez 2015 | ||
| Application note | DDR2 Memory Interface Clocks and Registers - Overview | 25 Mär 2009 | ||
| User guide | LOGIC Pocket Data Book (Rev. B) | 16 Jan 2007 | ||
| Application note | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 08 Jul 2004 | ||
| Application note | TI IBIS File Creation, Validation, and Distribution Processes | 29 Aug 2002 | ||
| User guide | ALVC Advanced Low-Voltage CMOS Including SSTL, HSTL, And ALB (Rev. B) | 01 Aug 2002 | ||
| Application note | Designing With Logic (Rev. C) | 01 Jun 1997 | ||
| Application note | Input and Output Characteristics of Digital Integrated Circuits | 01 Okt 1996 | ||
| Application note | Live Insertion | 01 Okt 1996 |
Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.
| Gehäuse | Pins | Herunterladen |
|---|---|---|
| NFBGA (NMJ) | 96 | Optionen anzeigen |
Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.
Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support.