이 제품의 최신 버전이 있습니다
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
TPS62650-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 2: –40°C to +105°C Ambient Operating
Temperature Range - Device HBM ESD Classification Level H2
- Device CDM ESD Classification Level C3B
- Device Temperature Grade 2: –40°C to +105°C Ambient Operating
- 86% Efficiency at 6-MHz Operation
- 38-µA Quiescent Current
- Wide VIN Range From 2.3 V to 5.5 V
- 6-MHz Regulated Frequency Operation
- Load and Line Transient
- ±2% PWM DC Voltage Accuracy
- Automatic PFM/PWM Mode Switching
- Low-Ripple Light-Load PFM
- I2C Compatible Interface up to 3.4 Mbps
- Pin-Selectable Output Voltage (VSEL)
- Internal Soft-Start, <150-µs Start-Up Time
- Current Overload and Thermal Shutdown Protection
- Three Surface-Mount External Components Required (One MLCC Inductor,
Two Ceramic Capacitors) - Complete Sub 1-mm Component Profile Solution
- Total Solution Size <13 mm2
- Available in a 9-Pin NanoFree (CSP) Package
The TPS62650-Q1 device is a high-frequency synchronous step-down dc-dc converter optimized for battery-powered portable applications. Intended for low-power applications, the TPS62650-Q1 supports up to 800-mA load current and allows the use of small, low-cost inductors and capacitors.
The device is ideal for mobile phones and similar portable applications powered by a single-cell Li-Ion battery. With an output voltage range adjustable via an I2C interface down to 0.75 V, the device supports low-voltage core power supplies for DSPs and processors in smart-phones and handheld computers.
The TPS62650-Q1 operates at a regulated 6-MHz switching frequency and enters the efficiency-optimized power-save mode operation at light load currents to maintain high efficiency over the entire load current range. In the shutdown mode, the current consumption is reduced to less than 3.5 µA.
The serial interface is compatible with Standard, Fast/Fast Plus and High-Speed mode I2C specification allowing transfers at up to 3.4 Mbps. This communication interface is used for dynamic voltage scaling with voltage steps down to 12.5 mV for setting the output voltage or reprogramming the mode of operation (PFM/PWM or Forced PWM), for instance.
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | 800-mA, 6-MHz High-Efficiency Step-Down Converter With I2C Compatible Interface datasheet (Rev. B) | 2012/12/27 | |
Application note | Performing Accurate PFM Mode Efficiency Measurements (Rev. A) | 2018/12/11 | ||
Analog Design Journal | Understanding 100% mode in low-power DC/DC converters | 2018/06/22 | ||
Analog Design Journal | Achieving a clean startup by using a DC/DC converter with a precise enable-pin threshold | 2017/10/24 | ||
Analog Design Journal | Testing tips for applying external power to supply outputs without an input voltage | 2016/10/24 | ||
Application note | Basic Calculation of a Buck Converter's Power Stage (Rev. B) | 2015/08/17 | ||
Analog Design Journal | Five steps to a great PCB layout for a step-down converter | 2015/01/29 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS62650 Unencrypted PSpice Transient Model Package (Rev. A)
패키지 | 핀 | 다운로드 |
---|---|---|
DSBGA (YFF) | 9 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치