設計工具
TLV2372
- Rail-to-Rail Input and Output
- Wide Bandwidth: 3 MHz
- High Slew Rate: 2.4 V/µs
- Supply Voltage Range: 2.7 V to 16 V
- Supply Current: 550 µA/Channel
- Low-Power Shutdown Mode
- IDD(SHDN): 25 µA/Channel
- Input Noise Voltage: 39 nV/√Hz
- Input Bias Current: 1 pA
- Specified Temperature Range:
- −40°C to +125°C (Industrial Grade)
- Ultra-Small Packaging:
- 5- or 6-Pin SOT-23 (TLV2370, TLV2371)
- 8- or 10-Pin MSOP (TLV2372, TLV2373)
The TLV237x single-supply operational amplifiers provide rail-to-rail input and output capability. The TLV237x takes the minimum operating supply voltage down to 2.7 V over the extended industrial temperature range while adding the rail-to-rail output swing feature. The TLV237x also provides 3-MHz bandwidth from only 550 µA. The maximum recommended supply voltage is 16 V, which allows the devices to be operated from (±8-V supplies down to ±1.35 V) a variety of rechargeable cells.
The CMOS inputs enable use in high-impedance sensor interfaces, with the lower voltage operation making an ideal alternative for the TLC227x in battery-powered applications. The rail-to-rail input stage further increases its versatility. The TLV237x is the seventh member of a rapidly growing number of RRIO products available from TI, and it is the first to allow operation up to 16-V rails with good ac performance.
All members are available in PDIP and SOIC with the singles in the small SOT-23 package, duals in the MSOP, and quads in the TSSOP package.
The 2.7-V operation makes the TLV237x compatible with Li-Ion powered systems and the operating supply voltage range of many micro-power microcontrollers available today including TI’s MSP430.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 5 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TLV237x 500-µA/Ch, 3-MHz Rail-to-Rail Input and Output Operational Amplifiers With Shutdown datasheet (Rev. F) | PDF | HTML | 2016年 8月 1日 |
| Circuit design | Slew-rate limiter circuit (Rev. A) | 2019年 2月 4日 | ||
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017年 3月 28日 | ||
| Application note | TLV2370/71/72/73/74/75 EMI Immunity Performance (Rev. A) | 2012年 11月 14日 | ||
| Application note | TLV2370/71/72/73/74/75 EMI Immunity Performance | 2012年 9月 24日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
DIP-ADAPTER-EVM — DIP 轉接器評估模組
Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.
The (...)
使用指南: PDF
開發板
DUAL-DIYAMP-EVM — 雙通道通用自製 (DIY) 放大器電路評估模組
The DUAL-DIYAMP-EVM is a unique evaluation module (EVM) family that provides engineers and do it yourselfers (DIYers) with real-world amplifier circuits, enabling you to quickly evaluate design concepts and verify simulations. It is designed specifically for dual package op amps in the (...)
使用指南: PDF
計算工具
ANALOG-ENGINEER-CALC — 類比工程師計算機
The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
設計工具
CIRCUIT060013 — 具有 T 網路回饋電路的反相放大器
此設計可反轉輸入訊號 VIN，並使用 1000 V/V 或 60 dB 訊號增益。具有 T 回饋網路的反相放大器可在沒有較小 R4 值或超大回饋電阻器值的情況下獲得高增益。
設計工具
CIRCUIT060059 — 轉換速率限制器電路
此電路控制類比增益階段的電壓轉換率。此電路適用於對稱電壓轉換率的應用。所需的電壓轉換率，必須比所選執行電壓轉換率限制器的運算放大器慢。
使用指南: PDF
設計工具
CIRCUIT060074 — 具有比較器電路的高壓側電流感測
此高壓側電流感測解決方案使用一個具有軌對軌輸入共模範圍的比較器，若負載電流上升到 1 A 以上，便在比較器輸出 (COMP OUT) 建立過電流警示 (OC 警示) 訊號。此實作中的 OC 訊號為低電位作動。因此當超過 1-A 閾值時，比較器輸出會變低。實作磁滯後會在負載電流降低至 0.5 A (減少 50%) 時，讓 OC-Alert 返回邏輯高狀態。此電路利用開漏輸出比較器，為控制數位邏輯輸入針腳而進行電平轉換輸出高邏輯電平。對於需要驅動 MOSFET 開關閘極的應用，建議使用具推挽輸出的比較器。
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
| 封裝 | 引腳 | 下載 |
|---|---|---|
| PDIP (P) | 8 | 檢視選項 |
| SOIC (D) | 8 | 檢視選項 |
| VSSOP (DGK) | 8 | 檢視選項 |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點