SLUSEE3 July   2021 BQ51013B-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Details of a Qi Wireless Power System and BQ51013B-Q1 Power Transfer Flow Diagrams
      2. 9.3.2  Dynamic Rectifier Control
      3. 9.3.3  Dynamic Efficiency Scaling
      4. 9.3.4  RILIM Calculations
      5. 9.3.5  Input Overvoltage
      6. 9.3.6  Adapter Enable Functionality and EN1/EN2 Control
      7. 9.3.7  End Power Transfer Packet (WPC Header 0x02)
      8. 9.3.8  Status Outputs
      9. 9.3.9  WPC Communication Scheme
      10. 9.3.10 Communication Modulator
      11. 9.3.11 Adaptive Communication Limit
      12. 9.3.12 Synchronous Rectification
      13. 9.3.13 Temperature Sense Resistor Network (TS)
      14. 9.3.14 3-State Driver Recommendations for the TS/CTRL Pin
      15. 9.3.15 Thermal Protection
      16. 9.3.16 WPC v1.2 Compliance – Foreign Object Detection
      17. 9.3.17 Receiver Coil Load-Line Analysis
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 BQ51013B-Q1 Wireless Power Receiver Used as a Power Supply
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 Using The BQ51013B-Q1 as a Wireless Power Supply: (See Figure 1-1 )
          2. 10.2.1.2.2 Series and Parallel Resonant Capacitor Selection
          3. 10.2.1.2.3 Recommended RX Coils
          4. 10.2.1.2.4 COMM, CLAMP, and BOOT Capacitors
          5. 10.2.1.2.5 Control Pins and CHG
          6. 10.2.1.2.6 Current Limit and FOD
          7. 10.2.1.2.7 RECT and OUT Capacitance
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Dual Power Path: Wireless Power and DC Input
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curves
      3. 10.2.3 Wireless and Direct Charging of a Li-Ion Battery at 800 mA
        1. 10.2.3.1 Design Requirements
        2. 10.2.3.2 Detailed Design Procedure
        3. 10.2.3.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
      2. 13.1.2 Development Support
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)(2)
MINMAXUNIT
Input voltageAC1, AC2–0.820V
RECT, COMM1, COMM2, OUT, CHG, CLAMP1, CLAMP2–0.320
AD, AD-EN–0.330
BOOT1, BOOT2–0.326
EN1, EN2(3), FOD, TS/CTRL, ILIM–0.37
Input currentAC1, AC22A(RMS)
Output currentOUT1.5A
Output sink currentCHG15mA
COMM1, COMM21A
Junction temperature, TJ–40150°C
Storage temperature, Tstg–65150°C
(1) All voltages are with respect to the VSS terminal, unless otherwise noted.
(2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(3) If EN1 or EN2 are subject to fast transient (>10V/10ns), current limiting resistors (1k to 10k ohms) should be added.