SWRS108B May   2011  – June 2014 CC113L

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Terminal Configuration and Functions
    1. 3.1 Pin Diagram
    2. 3.2 Signal Descriptions
  4. 4Specifications
    1. 4.1  Absolute Maximum Ratings
    2. 4.2  Handling Ratings
    3. 4.3  Recommended Operating Conditions
    4. 4.4  General Characteristics
    5. 4.5  Current Consumption
      1. 4.5.1 Typical RX Current Consumption over Temperature and Input Power Level, 868/915 MHz
    6. 4.6  RF Receive Section
      1. 4.6.1 Typical Sensitivity over Temperature and Supply Voltage, 868 MHz, Sensitivity Optimized Setting
      2. 4.6.2 Typical Sensitivity over Temperature and Supply Voltage, 915 MHz, Sensitivity Optimized Setting
      3. 4.6.3 Blocking and Selectivity
    7. 4.7  Crystal Oscillator
    8. 4.8  Frequency Synthesizer Characteristics
    9. 4.9  DC Characteristics
    10. 4.10 Power-On Reset
    11. 4.11 Thermal Characteristics
    12. 4.12 Typical Characteristics
      1. 4.12.1 Typical Characteristics, RX Current Consumption
      2. 4.12.2 Typical Characteristics, Blocking and Selectivity
  5. 5Detailed Description
    1. 5.1  Overview
    2. 5.2  Functional Block Diagram
    3. 5.3  Configuration Overview
    4. 5.4  Configuration Software
    5. 5.5  4-wire Serial Configuration and Data Interface
      1. 5.5.1 Chip Status Byte
      2. 5.5.2 Register Access
      3. 5.5.3 SPI Read
      4. 5.5.4 Command Strobes
      5. 5.5.5 RX FIFO Access
    6. 5.6  Microcontroller Interface and Pin Configuration
      1. 5.6.1 Configuration Interface
      2. 5.6.2 General Control and Status Pins
    7. 5.7  Data Rate Programming
    8. 5.8  Receiver Channel Filter Bandwidth
    9. 5.9  Demodulator, Symbol Synchronizer, and Data Decision
      1. 5.9.1 Frequency Offset Compensation
      2. 5.9.2 Bit Synchronization
      3. 5.9.3 Byte Synchronization
    10. 5.10 Packet Handling Hardware Support
      1. 5.10.1 Packet Format
        1. 5.10.1.1 Arbitrary Length Field Configuration
        2. 5.10.1.2 Packet Length > 255
      2. 5.10.2 Packet Filtering
        1. 5.10.2.1 Address Filtering
        2. 5.10.2.2 Maximum Length Filtering
        3. 5.10.2.3 CRC Filtering
      3. 5.10.3 Packet Handling in Receive Mode
      4. 5.10.4 Packet Handling in Firmware
    11. 5.11 Modulation Formats
      1. 5.11.1 Frequency Shift Keying
      2. 5.11.2 Amplitude Modulation
    12. 5.12 Received Signal Qualifiers and RSSI
      1. 5.12.1 Sync Word Qualifier
      2. 5.12.2 RSSI
      3. 5.12.3 Carrier Sense (CS)
        1. 5.12.3.1 CS Absolute Threshold
        2. 5.12.3.2 CS Relative Threshold
    13. 5.13 Radio Control
      1. 5.13.1 Power-On Start-Up Sequence
        1. 5.13.1.1 Automatic POR
        2. 5.13.1.2 Manual Reset
      2. 5.13.2 Crystal Control
      3. 5.13.3 Voltage Regulator Control
      4. 5.13.4 Receive Mode (RX)
      5. 5.13.5 RX Termination
      6. 5.13.6 Timing
        1. 5.13.6.1 Overall State Transition Times
        2. 5.13.6.2 Frequency Synthesizer Calibration Time
    14. 5.14 RX FIFO
    15. 5.15 Frequency Programming
    16. 5.16 VCO
      1. 5.16.1 VCO and PLL Self-Calibration
    17. 5.17 Voltage Regulators
    18. 5.18 General Purpose and Test Output Control Pins
    19. 5.19 Asynchronous and Synchronous Serial Operation
      1. 5.19.1 Asynchronous Serial Operation
      2. 5.19.2 Synchronous Serial Operation
    20. 5.20 System Consideration and Guidelines
      1. 5.20.1 SRD Regulations
      2. 5.20.2 Calibration in Multi-Channel Systems
    21. 5.21 Configuration Registers
      1. 5.21.1 Configuration Register Details - Registers with preserved values in SLEEP state
      2. 5.21.2 Configuration Register Details - Registers that Loose Programming in SLEEP State
      3. 5.21.3 Status Register Details
    22. 5.22 Development Kit Ordering Information
  6. 6Applications, Implementation, and Layout
    1. 6.1 Bias Resistor
    2. 6.2 Balun and RF Matching
      1. 6.2.1 Balun and RF Matching (Low-Cost Application Circuit)
      2. 6.2.2 Balun and RF Matching (Characterization Circuit)
    3. 6.3 Crystal
    4. 6.4 Reference Signal
    5. 6.5 Power Supply Decoupling
    6. 6.6 PCB Layout Recommendations
  7. 7Device and Documentation Support
    1. 7.1 Device Support
      1. 7.1.1 Device Nomenclature
    2. 7.2 Documentation Support
      1. 7.2.1 Related Documentation from Texas Instruments
      2. 7.2.2 Community Resources
    3. 7.3 Trademarks
    4. 7.4 Electrostatic Discharge Caution
    5. 7.5 Export Control Notice
    6. 7.6 Glossary
    7. 7.7 Additional Acronyms
  8. 8Mechanical Packaging and Orderable Information
    1. 8.1 Packaging Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8 Mechanical Packaging and Orderable Information

8.1 Packaging Information

The following pages include mechanical packaging and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.