SWRS227B March   2020  – May 2021 CC3130

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Functional Block Diagram
  5. 5 Revision History
  6. 6 Device Comparison
    1. 6.1 Related Products
  7. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Pin Attributes
    3. 7.3 Signal Descriptions
      1.      12
    4. 7.4 Connections for Unused Pins
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Power-On Hours (POH)
    4. 8.4  Recommended Operating Conditions
    5. 8.5  Current Consumption Summary
    6. 8.6  TX Power Control
    7. 8.7  Brownout and Blackout Conditions
      1. 8.7.1 Brownout and Blackout Voltage Levels
    8. 8.8  Electrical Characteristics for DIO Pins
      1. 8.8.1 Electrical Characteristics: DIO Pins Except 52 and 53
      2. 8.8.2 Electrical Characteristics: DIO Pins 52 and 53
    9. 8.9  Electrical Characteristics for Pin Internal Pullup and Pulldown
    10. 8.10 WLAN Receiver Characteristics
      1.      28
    11. 8.11 WLAN Transmitter Characteristics
      1.      30
    12. 8.12 WLAN Transmitter Out-of-Band Emissions
      1. 8.12.1 WLAN 2.4 GHz Filter Requirements
    13. 8.13 BLE/2.4 GHz Radio Coexistence and WLAN Coexistence Requirements
    14. 8.14 Thermal Resistance Characteristics for RGK Package
    15. 8.15 Timing and Switching Characteristics
      1. 8.15.1 Power Supply Sequencing
      2. 8.15.2 Device Reset
      3. 8.15.3 Reset Timing
        1. 8.15.3.1 nRESET (32-kHz Crystal)
        2. 8.15.3.2 First-Time Power-Up and Reset Removal Timing Requirements (32-kHz Crystal)
        3. 8.15.3.3 nRESET (External 32-kHz Crystal)
          1. 8.15.3.3.1 First-Time Power-Up and Reset Removal Timing Requirements (External 32-kHz Crystal)
      4. 8.15.4 Wakeup From HIBERNATE Mode
        1. 8.15.4.1 nHIB Timing Requirements
      5. 8.15.5 Clock Specifications
        1. 8.15.5.1 Slow Clock Using Internal Oscillator
          1. 8.15.5.1.1 RTC Crystal Requirements
        2. 8.15.5.2 Slow Clock Using an External Clock
          1. 8.15.5.2.1 External RTC Digital Clock Requirements
        3. 8.15.5.3 Fast Clock (Fref) Using an External Crystal
          1. 8.15.5.3.1 WLAN Fast-Clock Crystal Requirements
        4. 8.15.5.4 Fast Clock (Fref) Using an External Oscillator
          1. 8.15.5.4.1 External Fref Clock Requirements (–40°C to +85°C)
      6. 8.15.6 Interfaces
        1. 8.15.6.1 Host SPI Interface Timing
          1. 8.15.6.1.1 Host SPI Interface Timing Parameters
        2. 8.15.6.2 Flash SPI Interface Timing
          1. 8.15.6.2.1 Flash SPI Interface Timing Parameters
        3. 8.15.6.3 DIO Interface Timing
          1. 8.15.6.3.1 DIO Output Transition Time Parameters (Vsupply = 3.3 V)
            1. 8.15.6.3.1.1 DIO Output Transition Times (Vsupply = 3.3 V) (1)
          2. 8.15.6.3.2 DIO Input Transition Time Parameters
            1. 8.15.6.3.2.1 DIO Input Transition Time Parameters
    16. 8.16 External Interfaces
      1. 8.16.1 SPI Flash Interface
      2. 8.16.2 SPI Host Interface
      3. 8.16.3 Host UART Interface
        1. 8.16.3.1 5-Wire UART Topology
        2. 8.16.3.2 4-Wire UART Topology
        3. 8.16.3.3 3-Wire UART Topology
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Device Features
      1. 9.2.1 WLAN
      2. 9.2.2 Network Stack
      3. 9.2.3 Security
      4. 9.2.4 Host Interface and Driver
      5. 9.2.5 System
    3. 9.3 Power-Management Subsystem
      1. 9.3.1 VBAT Wide-Voltage Connection
    4. 9.4 Low-Power Operating Modes
      1. 9.4.1 Low-Power Deep Sleep
      2. 9.4.2 Hibernate
      3. 9.4.3 Shutdown
    5. 9.5 Memory
      1. 9.5.1 External Memory Requirements
    6. 9.6 Restoring Factory Default Configuration
    7. 9.7 Hostless Mode
  10. 10Applications, Implementation, and Layout
    1. 10.1 Application Information
      1. 10.1.1 BLE/2.4 GHz Radio Coexistence
      2. 10.1.2 Antenna Selection
      3. 10.1.3 Typical Application
    2. 10.2 PCB Layout Guidelines
      1. 10.2.1 General PCB Guidelines
      2. 10.2.2 Power Layout and Routing
        1. 10.2.2.1 Design Considerations
      3. 10.2.3 Clock Interface Guidelines
      4. 10.2.4 Digital Input and Output Guidelines
      5. 10.2.5 RF Interface Guidelines
  11. 11Device and Documentation Support
    1. 11.1 Tools and Software
    2. 11.2 Firmware Updates
    3. 11.3 Device Nomenclature
    4. 11.4 Documentation Support
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.6 TX Power Control

The CC3130 has several options for modifying the output power of the device when required. It is possible to lower the overall output power at a global level using the global TX power level setting. In addition, the 2.4 GHz band allows the user to enter additional back-offs (1), per channel, region (2)and modulation rates (3), via Image creator (see the UniFlash CC3x20, CC3x35 SimpleLink™ Wi-Fi® and Internet-on-a chip™ Solution ImageCreator and Programming Tool User's Guide for more details).

Figure 8-1, Figure 8-2, and Figure 8-3 show TX power and IBAT versus TX power level settings for the CC3130 device at modulations of 1 DSSS, 6 OFDM, and 54 OFDM, respectively.

In Figure 8-1, the area enclosed in the circle represents a significant reduction in current during transition from TX power level 3 to level 4. In the case of lower range requirements (14-dBm output power), TI recommends using TX power level 4 to reduce the current.

GUID-0230D56F-A13D-4412-9BE2-9F195B779F71-low.gifFigure 8-1 TX Power and IBAT vs TX Power Level Settings (1 DSSS)

 

 

GUID-0CEB5A6E-C13C-4469-97FB-E4ED21B608B6-low.gifFigure 8-2 TX Power and IBAT vs TX Power Level Settings (6 OFDM)
GUID-6CAA94A3-A024-46E1-BD21-DDA823B9B121-low.gifFigure 8-3 TX Power and IBAT vs TX Power Level Settings (54 OFDM)

 

1. The back-off range is between -6 dB to +6 dB in 0.25dB increments.
2. FCC/ISED, ETSI (Europe), and Japan are supported.
3. Back-off rates are grouped into 11b rates, high modulation rates (MCS7, 54 OFDM and 48 OFDM), and lower modulation rates (all other rates).