SCAS847J July   2007  – June 2025 CDCE925 , CDCEL925

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 EEPROM Specification
    7. 5.7 Timing Requirements: CLK_IN
    8. 5.8 Timing Requirements: SDA/SCL
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Control Terminal Setting
      2. 7.3.2 Default Device Setting
      3. 7.3.3 SDA/SCL Serial Interface
      4. 7.3.4 Data Protocol
    4. 7.4 Device Functional Modes
      1. 7.4.1 SDA/SCL Hardware Interface
    5. 7.5 Programming
  9. 8 Register Maps
    1. 8.1 SDA/SCL Configuration Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Spread-Spectrum Clock (SSC)
        2. 9.2.2.2 PLL Frequency Planning
        3. 9.2.2.3 Crystal Oscillator Start-Up
        4. 9.2.2.4 Frequency Adjustment With Crystal Oscillator Pulling
        5. 9.2.2.5 Unused Inputs and Outputs
        6. 9.2.2.6 Switching Between XO and VCXO Mode
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Development Support
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.2.2.2 PLL Frequency Planning

At a given input frequency (ƒIN), the output frequency (ƒOUT) of the CDCEx925 is calculated with Equation 1.

Equation 1. ƒOUT=ƒINPdiv×NM

where

  • M (1 to 511) and N (1 to 4095) are the multiplier/divide values of the PLL
  • Pdiv (1 to 127) is the output divider

The target VCO frequency (ƒVCO) of each PLL is calculated with Equation 2.

Equation 2. ƒVCO=ƒIN×NM

The PLL internally operates as fractional divider and needs the following multiplier/divider settings:

Equation 3. NP=4-intlog2NM if P<0 then P=0 Q=intN'MR=N'-M×Q

where

  • N′ = N × 2P
  • N ≥ M
  • 80MHz ≤ ƒVCO ≤ 230MHz
  • 16 ≤ q ≤ 63
  • 0 ≤ p ≤ 4
  • 0 ≤ r ≤ 511
Example:
for ƒIN = 27MHz; M = 1; N = 4; Pdiv = 2;for ƒIN = 27MHz; M = 2; N = 11; Pdiv = 2;
→fOUT = 54MHz→fOUT = 74.25MHz
→fVCO = 108MHz→fVCO = 148.50MHz
→P = 4 – int(log24) = 4 – 2 = 2→P = 4 – int(log25.5) = 4 – 2 = 2
→N′’ = 4 × 22 = 16→N′’ = 11 × 22 = 44
→Q = int(16) = 16→Q = int(22) = 22
→R = 16 – 16 = 0→R = 44 – 44 = 0

The values for P, Q, R, and N’ are automatically calculated when using TI Pro-Clock software.