SLLSF98 December   2018 SN55HVD233-SEP

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1.     Device Images
      1.      Simplified Schematic
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Driver Electrical Characteristics
    6. 7.6  Receiver Electrical Characteristics
    7. 7.7  Driver Switching Characteristics
    8. 7.8  Receiver Switching Characteristics
    9. 7.9  Device Switching Characteristics
    10. 7.10 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Modes
      2. 9.3.2 Loopback
      3. 9.3.3 CAN Bus States
      4. 9.3.4 ISO 11898 Compliance of SN55HVD233-SEP
        1. 9.3.4.1 Introduction
        2. 9.3.4.2 Differential Signal
          1. 9.3.4.2.1 Common-Mode Signal
        3. 9.3.4.3 Interoperability of 3.3-V CAN in 5-V CAN Systems
      5. 9.3.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Diagnostic Loopback
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Slope Control
        2. 10.2.2.2 Standby
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Bus Loading, Length, and Number of Nodes
      2. 12.1.2 CAN Termination
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Receiving Notification of Documentation Updates
    2. 13.2 Community Resources
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.5 Driver Electrical Characteristics

At TA = –55°C to 125°C, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
VO(D) Bus output voltage (dominant) CANH V(D) = 0 V, V(RS) = 0 V, see Figure 12 and Figure 13 2.4 VCC V
CANL 0.5 1.25
VO Bus output voltage (recessive) CANH V(D) = 3 V, V(RS) = 0 V, see Figure 12 and Figure 13 2.3 V
CANL 2.3
VOD(D) Differential output voltage (dominant) V(D) = 0 V, V(RS) = 0 V, see Figure 12 and Figure 13 1.5 2 3 V
V(D) = 0 V, V(RS) = 0 V, see Figure 13 and Figure 14 1.2 2 3
VOD Differential output voltage (recessive) V(D) = 3 V, V(RS) = 0 V, see Figure 12 and Figure 13 –120 12 mV
V(D) = 3 V, V(RS) = 0 V, no load –0.5 0.05 V
VOC(pp) Peak-to-peak common-mode output voltage See Figure 20 1 V
IIH High-level input current D, LBK V(D) = 2 V –30 30 µA
IIL Low-level input current D, LBK V(D) = 0.8 V –30 30 µA
IOS Short-circuit output current V(CANH) = –7 V, CANL open, see Figure 23 –250 mA
V(CANH) = 12 V, CANL open, see Figure 23 1
V(CANL) = –7 V, CANH open, see Figure 23 –1
V(CANL) = 12 V, CANH open, see Figure 23 250
CO Output capacitance See receiver input capacitance
IIRS(s) RS input current for standby V(RS) = 0.75 VCC –10 µA
ICC Supply current Standby V(RS) = VCC, V(D) = VCC, V(LBK) = 0 V 200 700 µA
Dominant V(D) = 0 V, no load, V(LBK) = 0 V, RS = 0 V 6 mA
Recessive V(D) = VCC, no load, V(LBK) = 0 V, V(RS) = 0 V 6
(1) All typical values are at 25°C and with a 3.3-V supply.