SLVSH51 july   2023 TPS631012 , TPS631013

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Rating
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics 
    6. 7.6 Timing Requirements
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Undervoltage Lockout (UVLO)
      2. 8.3.2 Enable and Soft Start
      3. 8.3.3 Device Enable (EN)
      4. 8.3.4 Output Voltage Control
      5. 8.3.5 Mode Selection (PFM/FPWM)
      6. 8.3.6 Output Discharge
      7. 8.3.7 Reverse Current Operation
      8. 8.3.8 Protection Features
        1. 8.3.8.1 Input Overvoltage Protection
        2. 8.3.8.2 Output Overvoltage Protection
        3. 8.3.8.3 Short Circuit Protection/Hiccup
        4. 8.3.8.4 Thermal Shutdown
    4. 8.4 Device Functional Modes
    5. 8.5 Programming
      1. 8.5.1 Serial Interface Description
      2. 8.5.2 Standard-, Fast-, and Fast-Mode Plus Protocol
      3. 8.5.3 I2C Update Sequence
    6. 8.6 Register Map
      1. 8.6.1 Register Description
        1. 8.6.1.1 Register Map
        2. 8.6.1.2 Register CONTROL1 (Register address: 0x02; Default: 0x08)
        3. 8.6.1.3 Register VOUT (Register address: 0x03; Default: 0x5C)
        4. 8.6.1.4 Register CONTROL2 (Register address: 0x05; Default: 0x45)
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Inductor Selection
        2. 9.2.2.2 Output Capacitor Selection
        3. 9.2.2.3 Input Capacitor Selection
        4. 9.2.2.4 Setting the Output Voltage
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.5.3 I2C Update Sequence

A single update requires the following:

  • A start condition
  • A valid I2C target address
  • A register address
  • A data byte

To acknowledge the receipt of each byte, the device pulls the SDA line low during the high period of a single clock pulse. The device performs an update on the falling edge of the acknowledge signal that follows the last byte.

GUID-20230718-SS0I-1GH6-S7NR-PWM9D8DCJGR9-low.svg Figure 8-8 “Write” Data Transfer Format in Standard, Fast, and Fast-Plus Modes
GUID-20230718-SS0I-R5JM-9V7G-4HV1FXW3FNCD-low.svg Figure 8-9 “Read” Data Transfer Format in Standard, Fast, and Fast-Plus Modes