SLVSG60A April   2023  – April 2024 TPS929160-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Device Bias and Power
        1. 6.3.1.1 Power Bias (VBAT)
        2. 6.3.1.2 Enable and Shutdown (EN)
        3. 6.3.1.3 5V Low-Drop-Out Linear Regulator (VLDO)
        4. 6.3.1.4 Undervoltage Lockout (UVLO) and Power-On-Reset (POR)
        5. 6.3.1.5 Power Supply (SUPPLY)
        6. 6.3.1.6 Programmable Low Supply Warning
      2. 6.3.2  Constant Current Output
        1. 6.3.2.1 Reference Current with External Resistor (REF)
        2. 6.3.2.2 64-Step Programmable High-Side Constant-Current Output
      3. 6.3.3  PWM Dimming
        1. 6.3.3.1 PWM Generator
        2. 6.3.3.2 PWM Dimming Frequency
        3. 6.3.3.3 Blank Time
        4. 6.3.3.4 Phase Shift PWM Dimming
        5. 6.3.3.5 Linear Brightness Control
        6. 6.3.3.6 Exponential Brightness Control
      4. 6.3.4  FAIL-SAFE State Operation
      5. 6.3.5  On-Chip, 8-Bit, Analog-to-Digital Converter (ADC)
        1. 6.3.5.1 Minimum On Time for ADC Measurement
        2. 6.3.5.2 ADC Auto Scan
        3. 6.3.5.3 ADC Error
      6. 6.3.6  NSTB Output
      7. 6.3.7  Diagnostic and Protection in NORMAL State
        1. 6.3.7.1  VBAT Undervoltage Lockout Diagnostics in NORMAL state
        2. 6.3.7.2  Low-Supply Warning Diagnostics in NORMAL State
        3. 6.3.7.3  Supply Undervoltage Diagnostics in NORMAL State
        4. 6.3.7.4  Reference Diagnostics in NORMAL state
        5. 6.3.7.5  Pre-Thermal Warning in NORMAL state
        6. 6.3.7.6  Overtemperature Protection in NORMAL state
        7. 6.3.7.7  Overtemperature Shutdown in NORMAL state
        8. 6.3.7.8  LED Open-Circuit Diagnostics in NORMAL state
        9. 6.3.7.9  LED Short-Circuit Diagnostics in NORMAL state
        10. 6.3.7.10 Single-LED Short-Circuit Detection in NORMAL state
        11. 6.3.7.11 EEPROM CRC Error in NORMAL state
        12. 6.3.7.12 Communication Loss Diagnostic in NORMAL state
        13. 6.3.7.13 Fault Masking in NORMAL state
        14.       55
      8. 6.3.8  Diagnostic and Protection in FAIL-SAFE states
        1. 6.3.8.1  Supply Undervoltage Lockout Diagnostics in FAIL-SAFE states
        2. 6.3.8.2  Low-Supply Warning Diagnostics in FAIL-SAFE states
        3. 6.3.8.3  Supply Undervoltage Diagnostics in FAIL-SAFE State
        4. 6.3.8.4  Reference Diagnostics in FAIL-SAFE states
        5. 6.3.8.5  Pre-Thermal Warning in FAIL-SAFE state
        6. 6.3.8.6  Overtemperature Protection in FAIL-SAFE state
        7. 6.3.8.7  Overtemperature Shutdown in FAIL-SAFE state
        8. 6.3.8.8  LED Open-Circuit Diagnostics in FAIL-SAFE state
        9. 6.3.8.9  LED Short-Circuit Diagnostics in FAIL-SAFE state
        10. 6.3.8.10 Single-LED Short-Circuit Detection in FAIL-SAFE state
        11. 6.3.8.11 EEPROM CRC Error in FAIL-SAFE state
        12. 6.3.8.12 Fault Masking in FAIL-SAFE state
        13.       69
      9. 6.3.9  OFAF Setup In FAIL-SAFE state
      10. 6.3.10 ERR Output
    4. 6.4 Device Functional Modes
      1. 6.4.1 POR State
      2. 6.4.2 INITIALIZATION state
      3. 6.4.3 NORMAL state
      4. 6.4.4 FAIL-SAFE state
      5. 6.4.5 PROGRAM state
    5. 6.5 Programming
      1. 6.5.1 FlexWire Protocol
        1. 6.5.1.1 Protocol Overview
        2. 6.5.1.2 UART Interface Address Setting
        3. 6.5.1.3 Status Response
        4. 6.5.1.4 Synchronization Byte
        5. 6.5.1.5 Device Address Byte
        6. 6.5.1.6 Register Address Byte
        7. 6.5.1.7 Data Frame
        8. 6.5.1.8 CRC Frame
        9. 6.5.1.9 Burst Mode
      2. 6.5.2 Registers Lock
      3. 6.5.3 Register Default Data
      4. 6.5.4 EEPROM Programming
        1. 6.5.4.1 Chip Selection by Pulling REF Pin High
        2. 6.5.4.2 Chip Selection by ADDR Pins Configuration
        3. 6.5.4.3 EEPROM Register Access and Burn
        4. 6.5.4.4 EEPROM PROGRAM state Exit
    6. 6.6 Register Maps
      1. 6.6.1 BRT Registers
      2. 6.6.2 IOUT Registers
      3. 6.6.3 CONF Registers
      4. 6.6.4 CTRL Registers
      5. 6.6.5 FLAG Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Smart Rear Lamp with Distributed LED Drivers
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
      4. 7.2.4 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • DCP|38
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.6.5 FLAG Registers

Table 6-137 lists the memory-mapped registers for the FLAG registers. All register offset addresses not listed in Table 6-137 should be considered as reserved locations and the register contents should not be modified.

FLAG Register

Table 6-137 FLAG Registers
OffsetAcronymRegister NameSection
A0hFLAG_ERRDevice Error Flag RegisterGo
A1hFLAG_STATUSDevice Status Flag RegisterGo
A2hFLAG_ADCSelected Channel ADC Measurement ResultGo
A3hFLAG_SLS0OUTAn, OUTBn Single-LED Short Error FLAGGo
A4hFLAG_SLS1OUTCn, OUTDn Single-LED Short Error FLAGGo
A5hFLAG_SLS2OUTEn, OUTFn Single-LED Short Error FLAGGo
A6hFLAG_SLS3OUTGn, OUTHn Single-LED Short Error FLAGGo
A7hFLAG_OPEN0OUTAn, OUTBn LED Open Error FLAGGo
A8hFLAG_OPEN1OUTCn, OUTDn LED Open Error FLAGGo
A9hFLAG_OPEN2OUTEn, OUTFn LED Open Error FLAGGo
AAhFLAG_OPEN3OUTGn, OUTHn LED Open Error FLAGGo
ABhFLAG_SHORT0OUTAn, OUTBn Short-to-GND Error FLAGGo
AChFLAG_SHORT1OUTCn, OUTDn Short-to-GND Error FLAGGo
ADhFLAG_SHORT2OUTEn, OUTFn Short-to-GND Error FLAGGo
AEhFLAG_SHORT3OUTGn, OUTHn Short-to-GND Error FLAGGo
AFhFLAG_EEPCRCEEPROM Calculated CRCGo

Complex bit access types are encoded to fit into small table cells. Table 6-138 shows the codes that are used for access types in this section.

Table 6-138 FLAG Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
Reset or Default Value
-nValue after reset or the default value

6.6.5.1 FLAG_ERR Register (Offset = A0h) [Reset = 01h]

FLAG_ERR is shown in Figure 6-131 and described in Table 6-139.

Return to the Summary Table.

Figure 6-131 FLAG_ERR Register
76543210
FLAG_LOWSUPFLAG_SUPUVFLAG_REFFLAG_PRETSDFLAG_TSDFLAG_EEPCRCFLAG_OUTFLAG_ERR
R-0hR-0hR-0hR-0hR-0hR-0hR-0hR-1h
Table 6-139 FLAG_ERR Register Field Descriptions
BitFieldTypeResetDescription
7FLAG_LOWSUPR0h Supply voltage low flag
0h = Supply voltage is above preset threshold.
1h = Supply voltage is below preset threshold.
6FLAG_SUPUVR0h Supply undervoltage fault flag
0h = No supply undervoltage fault is detected.
1h = Device has supply undervoltage fault detected.
5FLAG_REFR0h REF pin fault flag
0h = No REF pin fault is detected.
1h = Device has REF pin fault detected.
4FLAG_PRETSDR0h Overtemperature Pre warning flag
0h = No overtemperature pre-warning is detected.
1h = Device has triggered overtemperature pre-warning threshold.
3FLAG_TSDR0h Thermal shutdown flag
0h = No thermal shutdown fault is triggered.
1h = Device has triggered thermal shutdown fault.
2FLAG_EEPCRCR0h EEPROM CRC failure flag
0h = EEPROM CRC passes.
1h = EEPROM CRC fails.
1FLAG_OUTR0h Output fault flag
0h = No output fault is detected.
1h = Device has at least one fault detected on output channels.
0FLAG_ERRR1h Error flag
0h = No error flag.
1h = Device has at least one error flag.

6.6.5.2 FLAG_STATUS Register (Offset = A1h) [Reset = 01h]

FLAG_STATUS is shown in Figure 6-132 and described in Table 6-140.

Return to the Summary Table.

Figure 6-132 FLAG_STATUS Register
76543210
FLAG_EEPPARFLAG_EXTFS1FLAG_EXTFS0FLAG_PROGDONEFLAG_FSFLAG_ADCDONEFLAG_ADCERRFLAG_POR
R-0hR-0hR-0hR-0hR-0hR-0hR-0hR-1h
Table 6-140 FLAG_STATUS Register Field Descriptions
BitFieldTypeResetDescription
7FLAG_EEPPARR0h EEPROM parity error flag
0h = No internal EEPROM parity error is triggered.
1h = Internal EEPROM parity error is triggered.
6FLAG_EXTFS1R0h FS1 input status flag
0h = FS1 input is logic low.
1h = FS1 input is logic high.
5FLAG_EXTFS0R0h FS0 input status flag
0h = FS0 input is logic low.
1h = FS0 input is logic high.
4FLAG_PROGDONER0h EEPROM program completition flag
0h = EEPROM burning is not completed or not started.
1h = EEPROM burning is completed.
3FLAG_FSR0h FS state flag
0h = Device is not in Fail-safe state.
1h = Device is in Fail-safe state.
2FLAG_ADCDONER0h ADC measurement completition flag
0h = ADC measurement result is not available.
1h = ADC measurement result is available, read ADC_OUT or write ADCCHSEL to clear FLAG_ADCDONE.
1FLAG_ADCERRR0h ADC error flag
0h = No ADC error is triggered.
1h = ADC error is triggered.
0FLAG_PORR1h Power-On-Reset flag
0h = No POR is triggered.
1h = Device has triggered POR.

6.6.5.3 FLAG_ADC Register (Offset = A2h) [Reset = 00h]

FLAG_ADC is shown in Figure 6-133 and described in Table 6-141.

Return to the Summary Table.

Figure 6-133 FLAG_ADC Register
76543210
ADC_OUT
R-0h
Table 6-141 FLAG_ADC Register Field Descriptions
BitFieldTypeResetDescription
7-0ADC_OUTR0h ADC measurement result for selected channel

6.6.5.4 FLAG_SLS0 Register (Offset = A3h) [Reset = 00h]

FLAG_SLS0 is shown in Figure 6-134 and described in Table 6-142.

Return to the Summary Table.

Figure 6-134 FLAG_SLS0 Register
76543210
RESERVEDFLAG_SLSOUTB1FLAG_SLSOUTB0RESERVEDFLAG_SLSOUTA1FLAG_SLSOUTA0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-142 FLAG_SLS0 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SLSOUTB1R0h Single-LED short-circuit fault flag for OUTB1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
4FLAG_SLSOUTB0R0h Single-LED short-circuit fault flag for OUTB0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SLSOUTA1R0h Single-LED short-circuit fault flag for OUTA1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
0FLAG_SLSOUTA0R0h Single-LED short-circuit fault flag for OUTA0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.

6.6.5.5 FLAG_SLS1 Register (Offset = A4h) [Reset = 00h]

FLAG_SLS1 is shown in Figure 6-135 and described in Table 6-143.

Return to the Summary Table.

Figure 6-135 FLAG_SLS1 Register
76543210
RESERVEDFLAG_SLSOUTD1FLAG_SLSOUTD0RESERVEDFLAG_SLSOUTC1FLAG_SLSOUTC0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-143 FLAG_SLS1 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SLSOUTD1R0h Single-LED short-circuit fault flag for OUTD1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
4FLAG_SLSOUTD0R0h Single-LED short-circuit fault flag for OUTD0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SLSOUTC1R0h Single-LED short-circuit fault flag for OUTC1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
0FLAG_SLSOUTC0R0h Single-LED short-circuit fault flag for OUTC0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.

6.6.5.6 FLAG_SLS2 Register (Offset = A5h) [Reset = 00h]

FLAG_SLS2 is shown in Figure 6-136 and described in Table 6-144.

Return to the Summary Table.

Figure 6-136 FLAG_SLS2 Register
76543210
RESERVEDFLAG_SLSOUTF1FLAG_SLSOUTF0RESERVEDFLAG_SLSOUTE1FLAG_SLSOUTE0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-144 FLAG_SLS2 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SLSOUTF1R0h Single-LED short-circuit fault flag for OUTF1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
4FLAG_SLSOUTF0R0h Single-LED short-circuit fault flag for OUTF0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SLSOUTE1R0h Single-LED short-circuit fault flag for OUTE1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
0FLAG_SLSOUTE0R0h Single-LED short-circuit fault flag for OUTE0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.

6.6.5.7 FLAG_SLS3 Register (Offset = A6h) [Reset = 00h]

FLAG_SLS3 is shown in Figure 6-137 and described in Table 6-145.

Return to the Summary Table.

Figure 6-137 FLAG_SLS3 Register
76543210
RESERVEDFLAG_SLSOUTH1FLAG_SLSOUTH0RESERVEDFLAG_SLSOUTG1FLAG_SLSOUTG0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-145 FLAG_SLS3 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SLSOUTH1R0h Single-LED short-circuit fault flag for OUTH1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
4FLAG_SLSOUTH0R0h Single-LED short-circuit fault flag for OUTH0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SLSOUTG1R0h Single-LED short-circuit fault flag for OUTG1
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.
0FLAG_SLSOUTG0R0h Single-LED short-circuit fault flag for OUTG0
0h = Single-LED short-circuit fault is not detected.
1h = Single-LED short-circuit fault is detected.

6.6.5.8 FLAG_OPEN0 Register (Offset = A7h) [Reset = 00h]

FLAG_OPEN0 is shown in Figure 6-138 and described in Table 6-146.

Return to the Summary Table.

Figure 6-138 FLAG_OPEN0 Register
76543210
RESERVEDFLAG_OPENOUTB1FLAG_OPENOUTB0RESERVEDFLAG_OPENOUTA1FLAG_OPENOUTA0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-146 FLAG_OPEN0 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_OPENOUTB1R0h Output open-circuit fault flag for OUTB1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
4FLAG_OPENOUTB0R0h Output open-circuit fault flag for OUTB0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_OPENOUTA1R0h Output open-circuit fault flag for OUTA1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
0FLAG_OPENOUTA0R0h Output open-circuit fault flag for OUTA0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.

6.6.5.9 FLAG_OPEN1 Register (Offset = A8h) [Reset = 00h]

FLAG_OPEN1 is shown in Figure 6-139 and described in Table 6-147.

Return to the Summary Table.

Figure 6-139 FLAG_OPEN1 Register
76543210
RESERVEDFLAG_OPENOUTD1FLAG_OPENOUTD0RESERVEDFLAG_OPENOUTC1FLAG_OPENOUTC0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-147 FLAG_OPEN1 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_OPENOUTD1R0h Output open-circuit fault flag for OUTD1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
4FLAG_OPENOUTD0R0h Output open-circuit fault flag for OUTD0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_OPENOUTC1R0h Output open-circuit fault flag for OUTC1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
0FLAG_OPENOUTC0R0h Output open-circuit fault flag for OUTC0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.

6.6.5.10 FLAG_OPEN2 Register (Offset = A9h) [Reset = 00h]

FLAG_OPEN2 is shown in Figure 6-140 and described in Table 6-148.

Return to the Summary Table.

Figure 6-140 FLAG_OPEN2 Register
76543210
RESERVEDFLAG_OPENOUTF1FLAG_OPENOUTF0RESERVEDFLAG_OPENOUTE1FLAG_OPENOUTE0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-148 FLAG_OPEN2 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_OPENOUTF1R0h Output open-circuit fault flag for OUTF1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
4FLAG_OPENOUTF0R0h Output open-circuit fault flag for OUTF0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_OPENOUTE1R0h Output open-circuit fault flag for OUTE1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
0FLAG_OPENOUTE0R0h Output open-circuit fault flag for OUTE0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.

6.6.5.11 FLAG_OPEN3 Register (Offset = AAh) [Reset = 00h]

FLAG_OPEN3 is shown in Figure 6-141 and described in Table 6-149.

Return to the Summary Table.

Figure 6-141 FLAG_OPEN3 Register
76543210
RESERVEDFLAG_OPENOUTH1FLAG_OPENOUTH0RESERVEDFLAG_OPENOUTG1FLAG_OPENOUTG0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-149 FLAG_OPEN3 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_OPENOUTH1R0h Output open-circuit fault flag for OUTH1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
4FLAG_OPENOUTH0R0h Output open-circuit fault flag for OUTH0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_OPENOUTG1R0h Output open-circuit fault flag for OUTG1
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.
0FLAG_OPENOUTG0R0h Output open-circuit fault flag for OUTG0
0h = Output open-circuit fault is not detected.
1h = Output open-circuit fault is detected.

6.6.5.12 FLAG_SHORT0 Register (Offset = ABh) [Reset = 00h]

FLAG_SHORT0 is shown in Figure 6-142 and described in Table 6-150.

Return to the Summary Table.

Figure 6-142 FLAG_SHORT0 Register
76543210
RESERVEDFLAG_SHORTOUTB1FLAG_SHORTOUTB0RESERVEDFLAG_SHORTOUTA1FLAG_SHORTOUTA0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-150 FLAG_SHORT0 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SHORTOUTB1R0h Output short-circuit fault flag for OUTB1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
4FLAG_SHORTOUTB0R0h Output short-circuit fault flag for OUTB0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SHORTOUTA1R0h Output short-circuit fault flag for OUTA1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
0FLAG_SHORTOUTA0R0h Output short-circuit fault flag for OUTA0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.

6.6.5.13 FLAG_SHORT1 Register (Offset = ACh) [Reset = 00h]

FLAG_SHORT1 is shown in Figure 6-143 and described in Table 6-151.

Return to the Summary Table.

Figure 6-143 FLAG_SHORT1 Register
76543210
RESERVEDFLAG_SHORTOUTD1FLAG_SHORTOUTD0RESERVEDFLAG_SHORTOUTC1FLAG_SHORTOUTC0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-151 FLAG_SHORT1 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SHORTOUTD1R0h Output short-circuit fault flag for OUTD1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
4FLAG_SHORTOUTD0R0h Output short-circuit fault flag for OUTD0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SHORTOUTC1R0h Output short-circuit fault flag for OUTC1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
0FLAG_SHORTOUTC0R0h Output short-circuit fault flag for OUTC0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.

6.6.5.14 FLAG_SHORT2 Register (Offset = ADh) [Reset = 00h]

FLAG_SHORT2 is shown in Figure 6-144 and described in Table 6-152.

Return to the Summary Table.

Figure 6-144 FLAG_SHORT2 Register
76543210
RESERVEDFLAG_SHORTOUTF1FLAG_SHORTOUTF0RESERVEDFLAG_SHORTOUTE1FLAG_SHORTOUTE0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-152 FLAG_SHORT2 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SHORTOUTF1R0h Output short-circuit fault flag for OUTF1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
4FLAG_SHORTOUTF0R0h Output short-circuit fault flag for OUTF0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SHORTOUTE1R0h Output short-circuit fault flag for OUTE1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
0FLAG_SHORTOUTE0R0h Output short-circuit fault flag for OUTE0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.

6.6.5.15 FLAG_SHORT3 Register (Offset = AEh) [Reset = 00h]

FLAG_SHORT3 is shown in Figure 6-145 and described in Table 6-153.

Return to the Summary Table.

Figure 6-145 FLAG_SHORT3 Register
76543210
RESERVEDFLAG_SHORTOUTH1FLAG_SHORTOUTH0RESERVEDFLAG_SHORTOUTG1FLAG_SHORTOUTG0
R-0hR-0hR-0hR-0hR-0hR-0h
Table 6-153 FLAG_SHORT3 Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5FLAG_SHORTOUTH1R0h Output short-circuit fault flag for OUTH1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
4FLAG_SHORTOUTH0R0h Output short-circuit fault flag for OUTH0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
3-2RESERVEDR0h Reserved
1FLAG_SHORTOUTG1R0h Output short-circuit fault flag for OUTG1
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.
0FLAG_SHORTOUTG0R0h Output short-circuit fault flag for OUTG0
0h = Output short-circuit fault is not detected.
1h = Output short-circuit fault is detected.

6.6.5.16 FLAG_EEPCRC Register (Offset = AFh) [Reset = 00h]

FLAG_EEPCRC is shown in Figure 6-146 and described in Table 6-154.

Return to the Summary Table.

Figure 6-146 FLAG_EEPCRC Register
76543210
CALC_EEPCRC
R-0h
Table 6-154 FLAG_EEPCRC Register Field Descriptions
BitFieldTypeResetDescription
7-0CALC_EEPCRCR0h Calculated CRC result for all EEPROM