JAJSN99A December   2022  – September 2023 TPS25772-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Recommended Components
    5. 7.5  Thermal Information
    6. 7.6  Buck-Boost Regulator
    7. 7.7  CC Cable Detection Parameters
    8. 7.8  CC VCONN Parameters
    9. 7.9  CC PHY Parameters
    10. 7.10 Thermal Shutdown Characteristics
    11. 7.11 Oscillator Characteristics
    12. 7.12 ADC Characteristics
    13. 7.13 TVS Parameters
    14. 7.14 Input/Output (I/O) Characteristics
    15. 7.15 BC1.2 Characteristics
    16. 7.16 I2C Requirements and Characteristics
    17. 7.17 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Device Power Management and Supervisory Circuitry
        1. 9.3.1.1 VIN UVLO and Enable/UVLO
        2. 9.3.1.2 Internal LDO Regulators
      2. 9.3.2  TVSP Device Configuration and ESD Protection
      3. 9.3.3  Buck-Boost Regulator
        1. 9.3.3.1  Buck-Boost Regulator Operation
        2. 9.3.3.2  Switching Frequency, Frequency Dither, Phase-Shift and Synchronization
        3. 9.3.3.3  VIN Supply and VIN Over-Voltage Protection
        4. 9.3.3.4  Feedback Paths and Error Amplifiers
        5. 9.3.3.5  Transconductors and Compensation
        6. 9.3.3.6  Output Voltage DAC, Soft-Start and Cable Droop Compensation
        7. 9.3.3.7  VBUS Overvoltage Protection
        8. 9.3.3.8  VBUS Undervoltage Protection
        9. 9.3.3.9  Current Sense Resistor (RSNS) and Current Limit Operation
        10. 9.3.3.10 Buck-Boost Peak Current Limits
      4. 9.3.4  USB-PD Physical Layer
        1. 9.3.4.1 USB-PD Encoding and Signaling
        2. 9.3.4.2 USB-PD Bi-Phase Marked Coding
        3. 9.3.4.3 USB-PD Transmit (TX) and Receive (Rx) Masks
        4. 9.3.4.4 USB-PD BMC Transmitter
        5. 9.3.4.5 USB-PD BMC Receiver
        6. 9.3.4.6 Squelch Receiver
      5. 9.3.5  VCONN
      6. 9.3.6  Cable Plug and Orientation Detection
        1. 9.3.6.1 Configured as a Source
        2. 9.3.6.2 Configured as a Sink
        3. 9.3.6.3 Overvoltage Protection (Px_CC1, Px_CC2)
      7. 9.3.7  ADC
        1. 9.3.7.1 ADC Divider Ratios
      8. 9.3.8  BC 1.2, Legacy and Fast Charging Modes (Px_DP, Px_DM)
      9. 9.3.9  USB2.0 Low-Speed Endpoint
      10. 9.3.10 Digital Interfaces
        1. 9.3.10.1 General GPIO
        2. 9.3.10.2 I2C Buffer
      11. 9.3.11 I2C Interface
        1. 9.3.11.1 I2C Interface Description
        2. 9.3.11.2 I2C Clock Stretching
        3. 9.3.11.3 I2C Address Setting
        4. 9.3.11.4 Unique Address Interface
        5. 9.3.11.5 I2C Pullup Resistor Calculation
      12. 9.3.12 Digital Core
        1. 9.3.12.1 Device Memory
        2. 9.3.12.2 Core Microprocessor
      13. 9.3.13 NTC Input
      14. 9.3.14 Thermal Sensors and Thermal Shutdown
    4. 9.4 Device Functional Modes
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Application GUI Selections
        2. 10.2.2.2 EEPROM Selection
        3. 10.2.2.3 EN/UVLO
        4. 10.2.2.4 Sense Resistor, RSNS, RCSP, RCSN and CFILT
        5. 10.2.2.5 Inductor Currents
        6. 10.2.2.6 Output Capacitor
        7. 10.2.2.7 Input Capacitor
      3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.3.11.5 I2C Pullup Resistor Calculation

Typical value for RP, the I2C pullup resistor is given by:

RP = tr / (0.8473 × Cb)

Refer to Table 9-10 for values of tr, Cb and VOL.

Table 9-10 Parametrics from I2C Specifications
ParameterStandard Mode
(Max)		Fast Mode
(Max)		Fast Mode Plus
(Max)		Unit
fSCLSCL clock frequency1004001000kHz
trRise time of both SDA and SCL signals1000300120ns
CbCapacitive load for each bus line400400550pF
VOLLow-level output voltage (at 3-mA current sink, VDD > 2 V)0.40.40.4V
Low-level output voltage (at 2-mA current sink, VDD ≤ 2 V)–0.2 × VDD0.2 × VDDV

For additional background regarding I2C pullup resistor calculations, please refer to application report, I2C Bus Pullup Resistor Calculation.