JAJSJH9A
april 2023 – july 2023
TPS62876-Q1
PRODMIX
1
1
特長
2
アプリケーション
3
概要
4
Revision History
Device Options
5
Pin Configuration and Functions
6
Specifications
6.1
Absolute Maximum Ratings
6.2
ESD Ratings - Q100
6.3
Recommended Operating Conditions
6.4
Thermal Information
6.5
Electrical Characteristics
6.6
I2C Interface Timing Characteristics
6.7
Typical Characteristics
7
Parameter Measurement Information
8
Detailed Description
8.1
Overview
8.2
Functional Block Diagram
8.3
Feature Description
8.3.1
Fixed-Frequency DCS-Control Topology
8.3.2
Forced-PWM and Power-Save Modes
8.3.3
Transient Non-Synchronous Mode (optional)
8.3.4
Precise Enable
8.3.5
Start-Up
8.3.6
Switching Frequency Selection
8.3.7
Output Voltage Setting
8.3.7.1
Output Voltage Range
8.3.7.2
Output Voltage Setpoint
8.3.7.3
Non-Default Output Voltage Setpoint
8.3.7.4
Dynamic Voltage Scaling
8.3.7.5
Droop Compensation
8.3.8
Compensation (COMP)
8.3.9
Mode Selection / Clock Synchronization (MODE/SYNC)
8.3.10
Spread Spectrum Clocking (SSC)
8.3.11
Output Discharge
8.3.12
Undervoltage Lockout (UVLO)
8.3.13
Overvoltage Lockout (OVLO)
8.3.14
Overcurrent Protection
8.3.14.1
Cycle-by-Cycle Current Limiting
8.3.14.2
Hiccup Mode
8.3.14.3
Current-Limit Mode
8.3.15
Power Good (PG)
8.3.15.1
Standalone / Primary Device Behavior
8.3.15.2
Secondary Device Behavior
8.3.16
Remote Sense
8.3.17
Thermal Warning and Shutdown
8.3.18
Stacked Operation
8.4
Device Functional Modes
8.4.1
Power-On Reset
8.4.2
Undervoltage Lockout
8.4.3
Standby
8.4.4
On
8.5
Programming
8.5.1
Serial Interface Description
8.5.2
Standard-, Fast-, Fast-Mode Plus Protocol
8.5.3
HS-Mode Protocol
8.5.4
I2C Update Sequence
8.5.5
I2C Register Reset
8.5.6
Dynamic Voltage Scaling (DVS)
8.6
Device Registers
9
Application and Implementation
9.1
Application Information
9.2
Typical Application
9.2.1
Design Requirements
9.2.2
Detailed Design Procedure
9.2.2.1
Inductor Selection
9.2.2.2
Selecting the Input Capacitors
9.2.2.3
Selecting the Compensation Resistor
9.2.2.4
Selecting the Output Capacitors
9.2.2.5
Selecting the Compensation Capacitor CC
9.2.2.6
Selecting the Compensation Capacitor CC2
9.2.3
Application Curves
9.3
Application Using Two TPS62876-Q1 in a Stacked Configuration
9.3.1
Design Requirements For Two Stacked Devices
9.3.2
Detailed Design Procedure
9.3.2.1
Selecting the Compensation Resistor
9.3.2.2
Selecting the Output Capacitors
9.3.2.3
Selecting the Compensation Capacitor CC
9.3.3
Application Curves for Two Stacked Devices
9.4
Application Using Three TPS62876-Q1 in a Stacked Configuration
9.4.1
Design Requirements For Three Stacked Devices
9.4.2
Detailed Design Procedure
9.4.2.1
Selecting the Compensation Resistor
9.4.2.2
Selecting the Output Capacitors
9.4.2.3
Selecting the Compensation Capacitor CC
9.4.3
Application Curves for Three Stacked Devices
9.5
Best Design Practices
9.6
Power Supply Recommendations
9.7
Layout
9.7.1
Layout Guidelines
9.7.2
Layout Example
10
Device and Documentation Support
10.1
ドキュメントの更新通知を受け取る方法
10.2
サポート・リソース
10.3
Trademarks
10.4
静電気放電に関する注意事項
10.5
用語集
11
Mechanical, Packaging, and Orderable Information
パッケージ・オプション
メカニカル・データ(パッケージ|ピン)
RZV|24
MPQF690A
サーマルパッド・メカニカル・データ
発注情報
jajsjh9a_oa
1
特長
車載アプリケーション向けに AEC-Q100 認定済み
デバイス温度グレード 1:T
A
= -40℃~125℃
接合部温度範囲:-40℃~150℃
機能安全対応
機能安全準拠のシステム設計に役立つ資料を利用可能
入力電圧範囲:2.7V~6V
ピン互換デバイスのファミリ:15A、20A、25A
、30A
3 つの選択可能な出力電圧範囲:0.4V~1.675V
0.4V~0.71875V (1.25mV 刻み)
0.4V~1.0375V (2.5mV 刻み)
0.4V~1.675V (5mV 刻み)
出力電圧精度:±0.8%
内部電力 MOSFET:2.6mΩ および 1.5mΩ
調整可能なソフトスタート
外部補償
VSEL ピン
を介してスタートアップ出力電圧を選択可能
FSEL ピンを介して 1.5MHz、2.25MHz、2.5MHz、3MHz のスイッチング周波数を選択可能
強制 PWM またはパワー・セーブ・モード動作
外部抵抗または I
2
C によるスタートアップ出力電圧の選択
I
2
C 互換インターフェイス:最高 3.4MHz
オプションのスタック動作により、出力電流能力を向上
差動リモート・センス
サーマル事前警告およびサーマル・シャットダウン
出力放電
スペクトラム拡散クロック供給 (オプション)
ウィンドウ・コンパレータによるパワー・グッド出力