JAJSEF6L August   2013  – February 2019 TPS659038-Q1 , TPS659039-Q1

PRODUCTION DATA.  

  1. デバイスの概要
    1. 1.1 特長
    2. 1.2 アプリケーション
    3. 1.3 概要
    4. 1.4 ブロック概略図
  2. 改訂履歴
  3. Device Comparison
  4. Pin Configuration and Functions
    1. 4.1 Pin Functions
      1.      Pin Functions
    2. 4.2 Device Ball Mapping – 13 × 13 nFBGA, 169 Balls, 0,8-mm Pitch
    3. 4.3 Signal Descriptions
  5. Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Latch Up Rating
    6. 5.6  Electrical Characteristics: LDO Regulator
    7. 5.7  Electrical Characteristics: Dual-Phase (SMPS12 and SMPS45) and Triple-Phase (SMPS123 and SMPS457) Regulators
    8. 5.8  Electrical Characteristics: Stand-Alone Regulators (SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9)
    9. 5.9  Electrical Characteristics: Reference Generator (Bandgap)
    10. 5.10 Electrical Characteristics: 16-MHz Crystal Oscillator, 32-kHz RC Oscillator, and Output Buffers
    11. 5.11 Electrical Characteristics: DC-DC Clock Sync
    12. 5.12 Electrical Characteristics: 12-Bit Sigma-Delta ADC
    13. 5.13 Electrical Characteristics: Thermal Monitoring and Shutdown
    14. 5.14 Electrical Characteristics: System Control Thresholds
    15. 5.15 Electrical Characteristics: Current Consumption
    16. 5.16 Electrical Characteristics: Digital Input Signal Parameters
    17. 5.17 Electrical Characteristics: Digital Output Signal Parameters
    18. 5.18 Electrical Characteristics: I/O Pullup and Pulldown Resistance
    19. 5.19 I2C Interface Timing Requirements
    20. 5.20 SPI Timing Requirements
    21. 5.21 Typical Characteristics
  6. Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagrams
    3. 6.3 Feature Description
      1. 6.3.1  Power Management
      2. 6.3.2  Power Resources (Step-Down and Step-Up SMPS Regulators, LDOs)
        1. 6.3.2.1 Step-Down Regulators
          1. 6.3.2.1.1 Sync Clock Functionality
          2. 6.3.2.1.2 Output Voltage and Mode Selection
          3. 6.3.2.1.3 Current Monitoring and Short Circuit Detection
          4. 6.3.2.1.4 POWERGOOD
          5. 6.3.2.1.5 DVS-Capable Regulators
          6. 6.3.2.1.6 Non DVS-Capable Regulators
          7. 6.3.2.1.7 Step-Down Converters SMPS12 and SMPS123
            1.         a. Dual-Phase SMPS and Stand-Alone SMPS
            2.         b. Triple Phase SMPS
          8. 6.3.2.1.8 Step-Down Converter SMPS45 and SMPS457
          9. 6.3.2.1.9 Step-Down Converters SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9
        2. 6.3.2.2 LDOs – Low Dropout Regulators
          1. 6.3.2.2.1 LDOVANA
          2. 6.3.2.2.2 LDOVRTC
          3. 6.3.2.2.3 LDO Bypass (LDO9)
          4. 6.3.2.2.4 LDOUSB
          5. 6.3.2.2.5 Other LDOs
      3. 6.3.3  Long-Press Key Detection
      4. 6.3.4  RTC
        1. 6.3.4.1 General Description
        2. 6.3.4.2 Time Calendar Registers
          1. 6.3.4.2.1 TC Registers Read Access
          2. 6.3.4.2.2 TC Registers Write Access
        3. 6.3.4.3 RTC Alarm
        4. 6.3.4.4 RTC Interrupts
        5. 6.3.4.5 RTC 32-kHz Oscillator Drift Compensation
      5. 6.3.5  GPADC – 12-Bit Sigma-Delta ADC
        1. 6.3.5.1 Asynchronous Conversion Request (SW)
        2. 6.3.5.2 Periodic Conversion Request (AUTO)
        3. 6.3.5.3 Calibration
      6. 6.3.6  General-Purpose I/Os (GPIO Terminals)
        1. 6.3.6.1 REGEN Output
      7. 6.3.7  Thermal Monitoring
        1. 6.3.7.1 Hot-Die Function (HD)
        2. 6.3.7.2 Thermal Shutdown (TS)
        3. 6.3.7.3 Temperature Monitoring With External NTC Resistor or Diode
      8. 6.3.8  Interrupts
      9. 6.3.9  Control Interfaces
        1. 6.3.9.1 I2C Interfaces
          1. 6.3.9.1.1 I2C Implementation
          2. 6.3.9.1.2 F/S Mode Protocol
          3. 6.3.9.1.3 HS Mode Protocol
        2. 6.3.9.2 SPI Interface
          1. 6.3.9.2.1 SPI Modes
          2. 6.3.9.2.2 SPI Protocol
      10. 6.3.10 Device Identification
    4. 6.4 Device Functional Modes
      1. 6.4.1  Embedded Power Controller
      2. 6.4.2  State Transition Requests
        1. 6.4.2.1 ON Requests
        2. 6.4.2.2 OFF Requests
        3. 6.4.2.3 SLEEP and WAKE Requests
      3. 6.4.3  Power Sequences
      4. 6.4.4  Start Up Timing and RESET_OUT Generation
      5. 6.4.5  Power On Acknowledge
        1. 6.4.5.1 POWERHOLD Mode
        2. 6.4.5.2 AUTODEVON Mode
      6. 6.4.6  BOOT Configuration
        1. 6.4.6.1 Boot Terminal Selection
      7. 6.4.7  Reset Levels
      8. 6.4.8  Warm Reset
      9. 6.4.9  RESET_IN
      10. 6.4.10 Watchdog Timer (WDT)
      11. 6.4.11 System Voltage Monitoring
        1. 6.4.11.1 Generating a POR
  7. Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1  Recommended External Components
        2. 7.2.2.2  SMPS Input Capacitors
        3. 7.2.2.3  SMPS Output Capacitors
        4. 7.2.2.4  SMPS Inductors
        5. 7.2.2.5  LDO Input Capacitors
        6. 7.2.2.6  LDO Output Capacitors
        7. 7.2.2.7  VCC1
          1. 7.2.2.7.1 Meeting the Power Down Sequence
          2. 7.2.2.7.2 Maintaining Sufficient Input Voltage
        8. 7.2.2.8  VIO_IN
        9. 7.2.2.9  16-MHz Crystal
        10. 7.2.2.10 GPADC
      3. 7.2.3 Application Curves
  8. Power Supply Recommendations
  9. Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  10. 10デバイスおよびドキュメントのサポート
    1. 10.1 デバイス・サポート
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 デバイスの項目表記
    2. 10.2 ドキュメントのサポート
      1. 10.2.1 関連資料
    3. 10.3 関連リンク
    4. 10.4 ドキュメントの更新通知を受け取る方法
    5. 10.5 Community Resources
    6. 10.6 商標
    7. 10.7 静電気放電に関する注意事項
    8. 10.8 Glossary
  11. 11メカニカル、パッケージ、および注文情報
    1. 11.1 パッケージ・マテリアル情報

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • ZWS|169
サーマルパッド・メカニカル・データ
発注情報

BOOT Configuration

All TPS65903x-Q1 device series resource settings are stored under the form of registers. Therefore, any platform-related settings are linked to an action altering these registers. This action can be a static update (register initialization value) or a dynamic update of the register (either from the user or from a power sequence).

Resources and platform settings are stored in nonvolatile memory (OTP):

  • Static platform settings:
    • These settings define, for example, SMPS or LDO default voltages, GPIO functionality, and TPS65903x-Q1 switch-on events. Part of the static platform settings can have two different values, and these values are selected with the BOOT0 terminal. Static platform settings can be overwritten by a power sequence or by the user.
  • Sequence platform settings:
    • These settings define TPS65903x-Q1 power sequences between state transitions, for example, the OFF2ACT sequence when transitioning from OFF mode to ACTIVE mode. Each power sequence is composed of several register accesses that define which resources (and their corresponding registers) must be updated during the respective state transition. Three different sequences can be defined with the BOOT0 and BOOT1 terminals. These settings can be overwritten by the user once the power sequence completes its execution.

TPS659038-Q1 TPS659039-Q1 Boot_Pins_Control_SWCS095.gifFigure 6-24 Boot Terminal Control