SNAU287 November   2023

 

  1.   1
  2.   Description
  3.   Features
  4.   4
  5. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
  6. 2Hardware
    1. 2.1 Evaluation Setup Requirement
    2. 2.2 Configuring the EVM
      1. 2.2.1 Configuring the Power Supply
      2. 2.2.2 Configuring the Control Pins
      3. 2.2.3 Configuring the Clock Outputs
      4. 2.2.4 Using the USB Interface Connection
      5. 2.2.5 EVM Quick Start Guide
    3. 2.3 Modes of Operation
  7. 3Software
    1. 3.1 Using TICS Pro with the LMK3H0102EVM
      1. 3.1.1 Using the LMK3H0102 Wizard
        1. 3.1.1.1 Frequency Plan
        2. 3.1.1.2 Output Formats
        3. 3.1.1.3 Output Enable Pin
        4. 3.1.1.4 OTP Options
        5. 3.1.1.5 Review
        6. 3.1.1.6 Design Report
      2. 3.1.2 Live Debugger
        1. 3.1.2.1 FODs
        2. 3.1.2.2 Outputs
        3. 3.1.2.3 Others
      3. 3.1.3 Programming
        1. 3.1.3.1 Registers
        2. 3.1.3.2 OTP Configuration
      4. 3.1.4 Help
        1. 3.1.4.1 Contact TI
    2. 3.2 Using TI’s USB2ANY Module for In-System Programming of the LMK3H0102
      1. 3.2.1 USB2ANY Board Connections
      2. 3.2.2 Ordering a USB2ANY Module
  8. 4Hardware Design Files
    1. 4.1 Schematics
    2. 4.2 PCB Layout
    3. 4.3 Bill of Materials
  9. 5Additional Information
    1.     Trademarks
  10. 6Related Documentation

PCB Layout

GUID-20230417-SS0I-WWVP-HVMV-RKWS24WNGXGJ-low.gif Figure 4-5 Top Overlay
GUID-20230417-SS0I-4P9D-MRGF-M5RTVWJDCBRR-low.gif Figure 4-6 Top Solder Mask
GUID-20230417-SS0I-DLRT-HXDH-LVDVS9LN3XLG-low.gif Figure 4-7 Layer 1 (Top Side)
GUID-20230417-SS0I-G9QW-DC7N-G1LPNJWMGWK6-low.gif Figure 4-8 Signal Layer 1
GUID-20230417-SS0I-C8VC-PV6X-WQHV6FWS9XJS-low.gif Figure 4-9 Signal Layer 2
GUID-20230417-SS0I-S94N-KGG9-PTFHXSM8HDK5-low.gif Figure 4-10 Bottom Layer (View from Top)
GUID-20230417-SS0I-3BKH-KT9B-MDJFRK16LDKB-low.gif Figure 4-11 Bottom Solder Mask
GUID-20230417-SS0I-61GK-97ZP-8PBRWBCGXFNG-low.gif Figure 4-12 Bottom Overlay
GUID-20230417-SS0I-DVK9-NHJ1-XX9RL0MXMLFS-low.gif Figure 4-13 Drill Drawing