SBOU126A April   2012  – October 2026 INA3221 , INA3221-Q1

 

  1.   1
  2.   Description
  3.   Features
  4.   4
  5. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Device Information
  6. 2Hardware
    1. 2.1 Setup
      1. 2.1.1 INA3221 Hardware Theory of Operation
      2. 2.1.2 H1 Signal Definitions (10-Pin Male Connector Socket)
        1. 2.1.2.1 SM-USB-DIG Platform Theory of Operation
    2. 2.2 INA3221EVM Hardware Overview
      1. 2.2.1 Electrostatic Discharge Warning
      2. 2.2.2 Connecting the Hardware
      3. 2.2.3 Connecting the USB Cable to the SM-USB-DIG Platform
      4. 2.2.4 INA3221EVM Features
        1. 2.2.4.1 J3: I2C VS Control Setting
        2. 2.2.4.2 J1 and J2: I2C Address Hardware Setting (A0)
        3. 2.2.4.3 External I2C Lines and Terminal Block T1
        4. 2.2.4.4 Shunt Monitor Configuration and Terminal Blocks T3, T5, and T6
    3. 2.3 Power Requirements
      1. 2.3.1 Connecting Power
    4. 2.4 Jumper Information
      1. 2.4.1 Default Jumper Settings
  7. 3Software
    1. 3.1 INA3221EVM Software Setup
      1. 3.1.1 INA3221EVM Software Operating Systems
      2. 3.1.2 Software Installation
    2. 3.2 INA3221EVM Software Overview
      1. 3.2.1 Starting the INA3221EVM Software
      2. 3.2.2 Using the INA3221EVM Software
        1. 3.2.2.1 INA3221 Bus Voltage, Shunt Voltage, and Shunt Voltage Sum Reading Bar
        2. 3.2.2.2 Register Tab
        3. 3.2.2.3 Graph Tab
        4. 3.2.2.4 Auto-Write and DVDD Voltage
  8. 4Hardware Design Files
    1. 4.1 Schematic
    2. 4.2 PCB Layout
    3. 4.3 Bill of Materials
  9. 5Related Documentation
  10. 6Revision History

Default Jumper Settings

INA3221EVM Default Jumper Settings shows the default jumper configuration for the INA3221EVM. Some of the jumpers on the INA3221EVM board can be changed to match specific configuration requirements. For example, a specific I2C address can be set by configuring jumpers J1 and J2.

INA3221EVM INA3221EVM Default Jumper SettingsFigure 2-8 INA3221EVM Default Jumper Settings

Jumper 3 on the INA3221EVM is typically set to the INT position. When set to the INT position, the INA3221 supply voltage is generated and controlled by the SM-USB-DIG platform. When this jumper is set to the EXT position, VS connects to terminal strip T2.

Jumpers J1 and J2 control the INA3221 I2C address pin. These jumpers can set the address (A0) pin to either high, low, SCL, or SDA. Make sure to only connect one jumper at a time, never both. Failure to properly connect jumpers can cause shorts or interruptions in the communication lines. For more information on the INA3221 addressing, refer to the INA3221 product data sheet.

Table 2-2 summarizes the function of the INA3221 test board jumpers. For most applications, all jumpers must be left in the respective default configurations.

Table 2-2 INA3221EVM Test Board Jumper Functions
JumperDefaultPurpose
J1GNDThese jumpers select the I2C A0 address selection. Four separate I2C addresses can be selected, depending upon whether J1 is set high or low or whether J2 is set to SDA or SCL.
J2Open
J3INTThis jumper selects whether the INA3221 DVDD pin is connected to the VDUT signal generated from the SM-USB-DIG platform or whether the digital supply pin is connected to terminal T2, allowing for an external supply to power the digital circuitry. The default INT position connects the DVDD pin to the VDUT control signal.