SLASFB6A December   2025  – September 2026 MSPM33C321A

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagrams
    2. 6.2 Pin Attributes
      1.      10
    3. 6.3 Signal Descriptions
      1.      12
      2.      13
      3.      14
      4.      15
      5.      16
      6.      17
      7.      18
      8.      19
      9.      20
      10.      21
      11.      22
      12.      23
      13.      24
      14.      25
      15.      26
      16.      27
      17.      28
      18.      29
    4. 6.4 Connections for Unused Pins
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Supply Current Characteristics
      1. 7.5.1 RUN/SLEEP Modes
      2. 7.5.2 STOP/STANDBY Modes
      3. 7.5.3 SHUTDOWN Mode
      4. 7.5.4 VBAT current consumption
    6. 7.6  Flash Memory Characteristics
    7. 7.7  Power Supply Sequencing
      1. 7.7.1 Power Supply Ramp
      2. 7.7.2 POR and BOR
      3. 7.7.3 VBat Characteristics
      4. 7.7.4 Timing Characteristics
    8. 7.8  Clock Specifications
      1. 7.8.1 System Oscillator (SYSOSC)
      2. 7.8.2 High Frequency Crystal/Clock
      3. 7.8.3 System Phase Lock Loop (SYSPLL)
      4. 7.8.4 Low Frequency Oscillator (LFOSC)
      5. 7.8.5 Low Frequency Crystal/Clock
    9. 7.9  Analog Specifications
      1. 7.9.1 ADC Specifications
        1. 7.9.1.1 ADC Electrical Characteristics
        2. 7.9.1.2 ADC Switching Characteristics
        3. 7.9.1.3 ADC Linearity Parameters
        4. 7.9.1.4 Typical Connection Diagram
      2. 7.9.2 COMP Specifications
        1. 7.9.2.1 Comparator Electrical Characteristics
      3. 7.9.3 VREF Specifications
        1. 7.9.3.1 VREF Voltage Characteristics
        2. 7.9.3.2 VREF Electrical Characteristics
      4. 7.9.4 Analog VBOOST Specification
        1. 7.9.4.1 Analog Mux VBOOST
      5. 7.9.5 Temperature Sensor
    10. 7.10 Serial Interface Specifications
      1. 7.10.1 UART
        1. 7.10.1.1 UART
      2. 7.10.2 I2C
        1. 7.10.2.1 I2C Characteristics
        2. 7.10.2.2 I2C Filter
        3. 7.10.2.3 I2C Timing Diagram
      3. 7.10.3 SPI
        1. 7.10.3.1 SPI
        2. 7.10.3.2 SPI Timing Diagram
      4. 7.10.4 CAN
        1. 7.10.4.1 CAN
      5. 7.10.5 QSPI
        1. 7.10.5.1 QSPI
        2. 7.10.5.2 QSPI Timing Diagram
      6. 7.10.6 I2S/TDM
        1. 7.10.6.1 Serial Audio
        2. 7.10.6.2 I2S/TDM Timing Diagram
    11. 7.11 Digital IO
    12. 7.12 TRNG
      1. 7.12.1 TRNG Electrical Characteristics
      2. 7.12.2 TRNG Switching Characteristics
    13. 7.13 Emulation and Debug
      1. 7.13.1 SWD Timing
  9. 8 Detailed Description
    1. 8.1  Arm Cortex-M33 core with TrustZone and FPU
    2. 8.2  Power Management and Clock Unit (PMCU)
      1. 8.2.1 Power Management Unit (PMU)
      2. 8.2.2 Clock Module (CKM)
      3. 8.2.3 Operating Modes
        1. 8.2.3.1 Functionality by Operating Mode
    3. 8.3  Device Memory Map
      1. 8.3.1 Memory Organization
      2. 8.3.2 Peripheral Memory Map
    4. 8.4  NVIC Interrupt Map
    5. 8.5  Embedded Flash Memory
    6. 8.6  Embedded SRAM
    7. 8.7  DMA
    8. 8.8  Event Manager
    9. 8.9  Error Aggregator Module (EAM)
    10. 8.10 GPIO
    11. 8.11 IOMUX
      1. 8.11.1 Input/Output Diagrams
    12. 8.12 Analog Modules
      1. 8.12.1 HSADC
      2. 8.12.2 COMP
      3. 8.12.3 Temperature Sensor
      4. 8.12.4 VREF
      5. 8.12.5 Device Analog Connections
    13. 8.13 Security and Cryptography
      1. 8.13.1 Global Security Controller (GSC)
      2. 8.13.2 AESADV
      3. 8.13.3 SHA256
      4. 8.13.4 Public Key Algorithm (PKA)
      5. 8.13.5 TRNG
      6. 8.13.6 Keystore
      7. 8.13.7 CRC
    14. 8.14 Serial Communication Interfaces
      1. 8.14.1 UNICOMM (UART/I2C/SPI)
        1. 8.14.1.1 UART (UNICOMM)
        2. 8.14.1.2 I2C (UNICOMM)
        3. 8.14.1.3 SPI (UNICOMM)
      2. 8.14.2 CAN-FD
      3. 8.14.3 Quad SPI (QSPI)
      4. 8.14.4 Digital Audio Interface - I2S/TDM
    15. 8.15 LFSS
    16. 8.16 Timers, RTC_A and Watchdogs
      1. 8.16.1 Timers (TIMx)
      2. 8.16.2 RTC_A
      3. 8.16.3 IWDT
      4. 8.16.4 WWDT
    17. 8.17 Serial Wire Debug Interface
    18. 8.18 Bootstrap Loader (BSL)
    19. 8.19 Device Factory Constants
    20. 8.20 Identification
  10. 9 Applications, Implementation, and Layout
    1. 9.1 Typical Application
      1. 9.1.1 Schematic
  11. 10Device and Documentation Support
    1. 10.1 Getting Started and Next Steps
    2. 10.2 Device Nomenclature
    3. 10.3 Tools and Software
    4. 10.4 Documentation Support
    5. 10.5 Support Resources
    6. 10.6 Trademarks
    7. 10.7 Electrostatic Discharge Caution
    8. 10.8 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM

9.1.1 Schematic

TI recommends connecting a combination of a bulk decoupling capacitor (CVDD) and a small-value low-ESR ceramic decoupling capacitor (CDEC) across the VDD and VSS pins, as well as placing these capacitors as close as possible to the supply pins that they decouple (within a few millimeters) to achieve a minimal loop area. The CVDD bulk decoupling capacitor has a standard value referenced in the specifications section of the datasheet, but may be adjusted if needed based upon the PCB design and application requirements. For example, larger bulk capacitors can be used, but this can affect the supply rail ramp-up time.

The NRST reset pin must be pulled up to VDD (supply level) for the device to release from RESET state and start the boot process. TI recommends connecting an external pullup resistor (RpuNRST) with a pulldown capacitor (CNRST) for most applications to ensure that the default NRST state is logic-high (not triggering MCU reset), while also enabling the NRST pin to be controlled by another device or a debug probe.

A tank capacitor (CVCORE) is required for the VCORE pin to support the VCORE LDO supplying the digital logic rail in the MCU, and must be placed close to the device with minimum distance to the device ground. This VCORE pin is not meant to be used as a general-purpose LDO for external circuitry.

Note: Refer to the MSPM33 C-Series MCUs Hardware Development Guide for detailed application design guidance, such as recommended hardware connections and selection of external passive components.

MSPM33C321A MSPM33C3219 Basic Application Schematic

Figure 9-1 Basic Application Schematic