SLOS548A September   2007  – June 2026 TL082-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Electrical Characteristics
    4. 5.4 Operating Characteristics
    5. 5.5 Typical Characteristics
    6. 5.6 Old Versus New Die Comparison
  7. 6 Parameter Measurement Information
  8. 7 Application Information
    1. 7.1 Application Information Disclaimer
    2. 7.2 Application Information
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

9 Revision History

Changes from Revision * (September 2007) to Revision A (June 2026)

  • Updated the numbering format for tables, figures, and cross-references throughout the documentGo
  • Updated High Slew rate from 13V/μs to 21V/μs Go
  • Added Applications section Go
  • Updated the description as per new dieGo
  • Added package information tableGo
  • Deleted ordering information tableGo
  • Added Pin Functions tableGo
  • Removed ESD ratings parameterGo
  • Added ESD Ratings sectionGo
  • Updated Input Offset Voltage typical value from 3mV to ± 0.125mVGo
  • Updated Temperature Coefficient of Input Offset Voltage typical value from 18μV/°C to ± 0.3μV/°CGo
  • Updated Input Offset Current typical value from 5pA to ± 10pAGo
  • Updated Input Bias Current typical value from 30pA to ± 10pAGo
  • Updated Maximum peak output voltage swing typical value from 13.5V to 14.950VGo
  • Removed Maximum peak output voltage swing Full range values Go
  • Updated Large-signal differential voltage amplification at 25°C minimum value from 50V/mV to 94dB and typical value from 200V/mV to 130dB and Full range minimum value from 15V/mV to 83.5dBGo
  • Updated Unity-gain bandwidth from 3MHz to 4.5MHzGo
  • Updated Common-mode rejection ratio typical value from 86dB to 100dBGo
  • Updated Supply Voltage rejection ratio typical value from 86dB to 130dBGo
  • Updated Supply current typical from 1.4mA to 0.560mAGo
  • Removed Slew rate at unity gain minimum valueGo
  • Updated Slew rate at unity gain typical value from 13V/μs to 21V/μs for VID = 1VGo
  • Added Slew rate at unity gain typical value at VID = 100mV to reflect new die performanceGo
  • Removed Rise time and Overshoot factor specGo
  • Updated Equivalent input noise voltage at 1kHz typical value from 18nV/√Hz to 10.8nV/√Hz Go
  • Updated Equivalent input noise voltage from 0.1Hz to 10Hz typical value from 4μVPP to 1.8μVPP Go
  • Updated Equivalent input noise current typical value from 0.01pA/√ Hz to 2fA/√ Hz Go
  • Added New Die specifications for Total Harmonic DistortionGo
  • Updated plots as per New Die Characteristics Go
  • Added Old Versus New Die Comparison Go
  • Removed 100kHz Quadrature Oscillator from Application Information sectionGo