SLVSDR9F October   2016  – June 2026 DRV8702-Q1 , DRV8703-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 SPI Timing Requirements
    7. 5.7 Switching Characteristics
    8.     15
    9. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Bridge Control
        1. 6.3.1.1 Logic Tables
      2. 6.3.2  MODE Pin
      3. 6.3.3  nFAULT Pin
      4. 6.3.4  Current Regulation
      5. 6.3.5  Amplifier Output (SO)
        1. 6.3.5.1 SO Sample and Hold Operation
      6. 6.3.6  PWM Motor Gate Drivers
        1. 6.3.6.1 Miller Charge (QGD)
      7. 6.3.7  IDRIVE Pin (DRV8702-Q1 Only)
      8. 6.3.8  Dead Time
      9. 6.3.9  Propagation Delay
      10. 6.3.10 Overcurrent VDS Monitor
      11. 6.3.11 VDS Pin (DRV8702-Q1 Only)
      12. 6.3.12 Charge Pump
      13. 6.3.13 Gate Drive Clamp
      14. 6.3.14 Protection Circuits
        1. 6.3.14.1 VM Undervoltage Lockout (UVLO2)
        2. 6.3.14.2 Logic Undervoltage (UVLO1)
        3. 6.3.14.3 VCP Undervoltage Lockout (CPUV)
        4. 6.3.14.4 Overcurrent Protection (OCP)
        5. 6.3.14.5 Gate Driver Fault (GDF)
        6. 6.3.14.6 Thermal Shutdown (TSD)
        7. 6.3.14.7 Watchdog Fault (WDFLT, DRV8703-Q1 Only)
        8. 6.3.14.8 Reverse Supply Protection
      15. 6.3.15 Hardware Interface
        1. 6.3.15.1 IDRIVE (6-level input)
        2. 6.3.15.2 VDS (6-Level Input)
    4. 6.4 Device Functional Modes
    5. 6.5 Programming
      1. 6.5.1 SPI Communication
        1. 6.5.1.1 Serial Peripheral Interface (SPI)
        2. 6.5.1.2 SPI Format
  8. 7 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 External FET Selection
        2. 8.2.2.2 IDRIVE Configuration
        3. 8.2.2.3 VDS Configuration
        4. 8.2.2.4 Current Chopping Configuration
      3. 8.2.3 Application Curves
  10. 9 Power Supply Recommendations
    1. 9.1 Bulk Capacitance Sizing
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

6.3.14.8 Reverse Supply Protection

The circuit in Figure 6-17 can be implemented to help protect the system from reverse supply conditions. This circuit requires the following additional components:

  • NMOS FET
  • NPN BJT
  • Diode
  • 10-kΩ resistor
  • 43-kΩ resistor

DRV8702-Q1 DRV8703-Q1 Reverse Supply Protection Figure 6-17 Reverse Supply Protection