SLVSDR9F October   2016  – June 2026 DRV8702-Q1 , DRV8703-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 SPI Timing Requirements
    7. 5.7 Switching Characteristics
    8.     15
    9. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Bridge Control
        1. 6.3.1.1 Logic Tables
      2. 6.3.2  MODE Pin
      3. 6.3.3  nFAULT Pin
      4. 6.3.4  Current Regulation
      5. 6.3.5  Amplifier Output (SO)
        1. 6.3.5.1 SO Sample and Hold Operation
      6. 6.3.6  PWM Motor Gate Drivers
        1. 6.3.6.1 Miller Charge (QGD)
      7. 6.3.7  IDRIVE Pin (DRV8702-Q1 Only)
      8. 6.3.8  Dead Time
      9. 6.3.9  Propagation Delay
      10. 6.3.10 Overcurrent VDS Monitor
      11. 6.3.11 VDS Pin (DRV8702-Q1 Only)
      12. 6.3.12 Charge Pump
      13. 6.3.13 Gate Drive Clamp
      14. 6.3.14 Protection Circuits
        1. 6.3.14.1 VM Undervoltage Lockout (UVLO2)
        2. 6.3.14.2 Logic Undervoltage (UVLO1)
        3. 6.3.14.3 VCP Undervoltage Lockout (CPUV)
        4. 6.3.14.4 Overcurrent Protection (OCP)
        5. 6.3.14.5 Gate Driver Fault (GDF)
        6. 6.3.14.6 Thermal Shutdown (TSD)
        7. 6.3.14.7 Watchdog Fault (WDFLT, DRV8703-Q1 Only)
        8. 6.3.14.8 Reverse Supply Protection
      15. 6.3.15 Hardware Interface
        1. 6.3.15.1 IDRIVE (6-level input)
        2. 6.3.15.2 VDS (6-Level Input)
    4. 6.4 Device Functional Modes
    5. 6.5 Programming
      1. 6.5.1 SPI Communication
        1. 6.5.1.1 Serial Peripheral Interface (SPI)
        2. 6.5.1.2 SPI Format
  8. 7 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 External FET Selection
        2. 8.2.2.2 IDRIVE Configuration
        3. 8.2.2.3 VDS Configuration
        4. 8.2.2.4 Current Chopping Configuration
      3. 8.2.3 Application Curves
  10. 9 Power Supply Recommendations
    1. 9.1 Bulk Capacitance Sizing
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

6.3.14.3 VCP Undervoltage Lockout (CPUV)

If the voltage on the VCP pin falls below the threshold voltage of the charge-pump undervoltage (CPUV) lockout, all FETs in the H-bridge are disabled and the nFAULT pin is driven low. The DRV8703-Q1 the VCP_UVFL bit is set. The operation resumes when the VCP voltage rises above the CPUV threshold. The nFAULT pin is released after the operation resumes but the VCP_UVFL bit on the DRV8703-Q1 device remains set until cleared by writing to the CLR_FLT bit.