SNVSCQ0A March   2025  – September 2026 LP5814

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Dimming
      2. 7.3.2 PWM Dimming
      3. 7.3.3 Sloper
      4. 7.3.4 Autonomous Animation Control
        1. 7.3.4.1 Animation Engine Unit
        2. 7.3.4.2 Animation Pattern Unit
        3. 7.3.4.3 Animation Control
      5. 7.3.5 Protections
        1. 7.3.5.1 UVLO
        2. 7.3.5.2 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Initialization Mode
      2. 7.4.2 Standby and Normal Mode
      3. 7.4.3 Shutdown Mode
      4. 7.4.4 Thermal Shutdown Mode
    5. 7.5 Programming
      1. 7.5.1 I2C Data Tansactions
      2. 7.5.2 I2C Data Format
      3. 7.5.3 Command Description
    6. 7.6 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Parameters
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Program Procedure
        2. 8.2.3.2 Programming Example
      4. 8.2.4 Application Performance Plots
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

8.2.3.1 Program Procedure

After VCC powering up, the device is enabled by setting CHIP_EN = 1. Set the maximum current for each output. Then set the device configuration registers to enable the output, select the dimming control mode for each output, and select the animation engine for the output in autonomous animation mode. Finally, Send UPDATE_CMD to make the prior configuration settings take effect.

For the output channel that is configured in manual mode, the output PWM changes immediately when the corresponding manual PWM register value is set.

For the output channel that is configured in autonomous animation mode, firstly, select animation engine for output. Secondly, construct the animation engine by setting the engine configure registers to select the animation pattern to map to the engine order and enable or disable the engine order. Then, build the animation patterns as required by setting pattern unit parameters. Finally, send START_CMD to initiate the autonomous animation.

The detailed program procedure is illustrated in Figure 8-2.


LP5814 Program Procedure

Figure 8-2 Program Procedure