SNVSCS6A March   2026  – August 2026 TPS7H1301-SP

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Options Table
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Quality Conformance Inspection
    7. 7.7 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Enable
      2. 9.3.2  Charge Pump
        1. 9.3.2.1 Charge Pump Operation
        2. 9.3.2.2 Foldback Switching
      3. 9.3.3  Startup
      4. 9.3.4  Power Good
      5. 9.3.5  Output Voltage
      6. 9.3.6  Dropout
      7. 9.3.7  Output Voltage Accuracy
      8. 9.3.8  Output Noise
      9. 9.3.9  Power Supply Rejection Ratio
      10. 9.3.10 Stability
        1. 9.3.10.1 Stability of the TPS7H1301
        2. 9.3.10.2 Stability of the TPS7H1302
      11. 9.3.11 Thermal Shutdown
    4. 9.4 Device Functional Modes
      1. 9.4.1 Enable Disable
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application TPS7H1301
      1. 10.2.1 Design Requirements TPS7H1301
      2. 10.2.2 Detailed Design Procedure TPS7H1301
        1. 10.2.2.1 Capacitor Selection
          1. 10.2.2.1.1 Input Capacitor (CIN) Selection
          2. 10.2.2.1.2 CFLY TPS7H1301
          3. 10.2.2.1.3 CPOUT Capacitor TPS7H1301
          4. 10.2.2.1.4 Bypass Capacitors
          5. 10.2.2.1.5 Output Capacitor
        2. 10.2.2.2 Charge Pump Output Resistance
        3. 10.2.2.3 Configuring LDO Output
        4. 10.2.2.4 Output Noise
        5. 10.2.2.5 PSRR Design Implications
        6. 10.2.2.6 Stability Design Considerations
      3. 10.2.3 Application Curves
    3. 10.3 Typical Application TPS7H1301 Parallel Operation
      1. 10.3.1 Design Requirements
      2. 10.3.2 Detailed Design Procedure Parallel TPS7H1301
        1. 10.3.2.1 Parallel Ballast Resistor
      3. 10.3.3 Application Performance Plots
    4. 10.4 Typical Application TPS7H1302
      1. 10.4.1 Design Requirements TPS7H1302
      2. 10.4.2 Detailed Design Procedure TPS7H1302
        1. 10.4.2.1 Capacitor Selection TPS7H1302
        2. 10.4.2.2 CFLY Capacitor TPS7H1302
        3. 10.4.2.3 CPOUT Capacitor TPS7H1302
        4. 10.4.2.4 Stability TPS7H1302
      3. 10.4.3 TPS7H1302 Application Performance Plots
    5. 10.5 TPS7H1302 Low Noise Configuration
      1. 10.5.1 Design Requirements TPS7H1302 Low Noise
      2. 10.5.2 Application Performance Plots
    6. 10.6 Power Supply Recommendations
    7. 10.7 Layout
      1. 10.7.1 Layout Guidelines
      2. 10.7.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 13.1 Tube Information
    3.     88

8 Parameter Measurement Information

TPS7H1301-SP TPS7H1302-SP Dropout Current Measurement
A. VOUT(NOM) is the measured output voltage. VLIM is the specified percentage of output voltage permitted to rise above the specified VOUT(NOM). Iload is the load current applied on VOUT. When VOUT falls to 98% of the nominal value (VOUT(NOM)), the dropout current is recorded.
Figure 8-1 Dropout Current Measurement
TPS7H1301-SP TPS7H1302-SP Line Regulation Measurement
A. Line regulation ΔVOUT / ΔVIN = 100µV/V (typ). For example a 1V change in VIN (ΔVIN = 1V), results in a 100µV change in VOUT (ΔVOUT = 100µV). Line regulation is a DC parameter; therefore this waveform can only be considered valid after transients die out or for a slow VIN slew rate.
Figure 8-2 Line Regulation Measurement
TPS7H1301-SP TPS7H1302-SP Load Regulation Measurement
A. Load regulation: ΔVOUT / ΔIOUT = 8mV/A (typ). For example a 100mA change in IOUT (ΔIOUT = 100mA), results in a 0.8mV (typ TPS7H1301) change in VOUT (ΔVOUT = 0.8mV). Load regulation is a DC parameter; therefore this waveform can be considered valid after transients die out or for a slow IOUT slew rate.
Figure 8-3 Load Regulation Measurement
TPS7H1301-SP TPS7H1302-SP Enable Power Good Timing Measurement Figure 8-4 Enable Power Good Timing Measurement