SPRUJ51C June   2023  – October 2026

 

  1.   1
  2.   Description
  3.   Applications
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Device Information
    4. 1.4 EVM Revisions and Assembly Variants
    5. 1.5 Specification
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Memory
      3. 2.2.3 JTAG Emulator
      4. 2.2.4 Supported Interfaces and Peripherals
      5. 2.2.5 Expansion Connectors Headers to Support Application Specific Add On Boards
    3. 2.3  Power
      1. 2.3.1 Power Requirements
      2. 2.3.2 Power Input
      3. 2.3.3 Power Supply
      4. 2.3.4 Power ON OFF Procedures
        1. 2.3.4.1 Power-On Procedure
        2. 2.3.4.2 Power-Off Procedure
        3. 2.3.4.3 Power Test Points
      5. 2.3.5 Power Sequencing
      6. 2.3.6 AM62x 17x17 SoC Power
      7. 2.3.7 Current Monitoring
    4. 2.4  AM62x-Low Power SK EVM Interface Mapping
    5. 2.5  Clocking
    6. 2.6  Reset
    7. 2.7  OLDI Display Interface
    8. 2.8  CSI Interface
    9. 2.9  Audio Codec Interface
    10. 2.10 HDMI Display Interface
    11. 2.11 JTAG Interface
    12. 2.12 Test Automation Header
    13. 2.13 UART Interface
    14. 2.14 USB Interface
      1. 2.14.1 USB2.0 Type A Interface
      2. 2.14.2 USB2.0 Type-C Interface
    15. 2.15 Memory Interfaces
      1. 2.15.1 LPDDR4 Interface
      2. 2.15.2 OSPI
      3. 2.15.3 MMC Interfaces
        1. 2.15.3.1 MMC0 - eMMC Interface
        2. 2.15.3.2 MMC1 - Micro SD Interface
        3. 2.15.3.3 MMC2 - M2 Key E Interface
      4. 2.15.4 EEPROM
    16. 2.16 Ethernet Interface
      1. 2.16.1 CPSW Ethernet PHY1 Default Configuration
      2. 2.16.2 CPSW Ethernet PHY2 Default Configuration
    17. 2.17 GPIO Port Expander
    18. 2.18 GPIO Mapping
    19. 2.19 AM62x-Low Power SK EVM User Setup and Configuration
      1. 2.19.1 EVM DIP Switches
      2. 2.19.2 Boot Modes
      3. 2.19.3 User Test LEDs
    20. 2.20 Expansion Headers
      1. 2.20.1 User Expansion Connector
      2. 2.20.2 MCU Connector
      3. 2.20.3 PRU Connector
    21. 2.21 Push Buttons
    22. 2.22 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 EMC, EMI and ESD Compliance
  10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
      1. 5.1.1 Issue 1 – Wake-up from LPM Through MCU and WKUP UART Not Functioning
      2. 5.1.2 Issue 2 – Partial IO Low Power Mode entry/exit failure
    2.     Trademarks
    3.     75
  11. 6References
  12. 7Revision History

Power Requirements

Power the AM62x-Low Power SK EVM through either of the two USB Type-C Connectors.

Table 2-1 USB Type-C Connectors
Connector Power Role Data Role
Connector 1 (J13) SINK None
Connector 2 (J15) DRP USB2.0 DFP or UFP

The AM62x-Low Power SK EVM supports voltage input from 5V to 15V and 3A of current. A USB PD controller (manufacturer part number: TPS65988DHRSHR) is used for PD negotiation upon cable detection to get necessary power required for the board. Connector 1 is configured as an UFP Port and has no Data role. Connector 2 is configured as a DRP port and can act as DFP only when Connector 1 powers the board. When both the connectors are connected to external power supply, the port with highest PD power contract powers the board.

Table 2-2 Type-C port Power roles
J13 (UFP) J15 (DRP) Board Power Remarks
Plugged in NC ON - J13 J13 acts as the UFP and only sinks power and J15 can act as DFP if a peripheral is connected
NC Plugged in ON - J15 J15 acts as the UFP and can only sink power
Plugged in Plugged in ON- J13 or J15 The port with highest PD power contract powers the board

The PD IC uses a SPI EEPROM to load the necessary configuration on power up so that the PD IC can negotiate a power contract with a compatible power source.

The configuration file is loaded to the EEPROM using header J23. Once the EEPROM is programmed the PD obtains the configuration files via SPI communication. Upon loading the configuration files the PD negotiates with the source to obtain the necessary power requirement.

Power indication LEDs are provided for both the Type-C connectors for the user to identify which connector is powering the SKEVM Board. An external power supply (Type-C output) can be used to power the EVM but is not included as part of the SKEVM kit.
Table 2-3 Recommended External Power Supplies
DigiKey Part Number Manufacturer Manufacturer Part Number
1939-1794-ND GlobTek®, Inc. TR9CZ3000USBCG2R6BF21
Q1251-ND Qualtek® QADC-65-20-08CB
  1. This is the adapter part number used for compliance testing.
Note:
  • Minimum Voltage: 5VDC
  • Recommended Minimum Current: 3000mA
  • Maximum Voltage: 15VDC
  • Maximum current: 5000mA
Because SK-AM62-LP implements USB PD for power, the device can negotiate to the highest voltage and current combination supported by both the Device and power adapter. The power supply can exceed the maximum voltage and current requirements listed above if the power adapter is compliant with the USB-C® PD specification.
Note: TI recommends using an external power supply or power accessory which complies with applicable regional safety standards such as (by example) UL, CSA, VDE, CCC, or PSE.