Startseite Batteriemanagement-ICs Batterielader-ICs
Startseite
Batteriemanagement-ICs
Batterielader-ICs

BQ24140

AKTIV

Switchmode-Lader, 1,5 A, zwei Eingänge, mit USB-OTG-Unterstützung

Jetzt bestellen
Datenblatt

BQ24140

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer Charge current (max) (A) 1.5 Features BAT temp thermistor monitoring (hot/cold profile), Input OVP, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 4 Vin (max) (V) 9 Absolute max Vin (max) (V) 20 Control topology Switch-Mode Buck Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Control interface I2C Operating temperature range (°C) -40 to 85
Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer Charge current (max) (A) 1.5 Features BAT temp thermistor monitoring (hot/cold profile), Input OVP, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 4 Vin (max) (V) 9 Absolute max Vin (max) (V) 20 Control topology Switch-Mode Buck Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Control interface I2C Operating temperature range (°C) -40 to 85
DSBGA (YFF) 30 5.71999999999999912 mm² 2.2 x 2.5999999999999996
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • Charge Battery and Provide USB-OTG Support at the Same Time
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy: ±5% (100mA, 500mA)
    • Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0-125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery): 2.3V to 4.5V
    • Output for VBUS: 5.05V/500 mA
  • Input Voltage Based Dynamic Power Management Provides
    Protection Against Current Limited Adapters
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Added Security by Limiting
    Maximum Charge Voltage and Maximum Charge Current
  • 20-V Absolute Maximum Input Voltage Rating
  • 9.0-V Maximum Operating Input Voltage
  • Charge Faster than Linear Chargers
  • Built-in Input Current Sensing and Limiting
  • Integrated Power FETs for up to 1.5-A Charge Rate
  • Programmable Charge Parameters Through I2C Interface
    (up to 3.4 Mbps):
    • Input Current
    • Fast-Charge/Termination Current
    • Charge Voltage (3.5-4.44V)
    • Safety Timer with Reset Control
    • Safety Timer with Reset Control
    • Termination Enable
  • Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz
    With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery Drainage
    • Thermal Regulation and Protection
    • Input/Output Over Voltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • 2.35 × 2.65 mm 30-pin WCSP Package
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • Charge Battery and Provide USB-OTG Support at the Same Time
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy: ±5% (100mA, 500mA)
    • Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0-125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery): 2.3V to 4.5V
    • Output for VBUS: 5.05V/500 mA
  • Input Voltage Based Dynamic Power Management Provides
    Protection Against Current Limited Adapters
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Added Security by Limiting
    Maximum Charge Voltage and Maximum Charge Current
  • 20-V Absolute Maximum Input Voltage Rating
  • 9.0-V Maximum Operating Input Voltage
  • Charge Faster than Linear Chargers
  • Built-in Input Current Sensing and Limiting
  • Integrated Power FETs for up to 1.5-A Charge Rate
  • Programmable Charge Parameters Through I2C Interface
    (up to 3.4 Mbps):
    • Input Current
    • Fast-Charge/Termination Current
    • Charge Voltage (3.5-4.44V)
    • Safety Timer with Reset Control
    • Safety Timer with Reset Control
    • Termination Enable
  • Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz
    With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery Drainage
    • Thermal Regulation and Protection
    • Input/Output Over Voltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • 2.35 × 2.65 mm 30-pin WCSP Package

The bq24140 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates two synchronous PWM chargers, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, the IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to 125°C typical. To support USB OTG device, the IC can provide VBUS (5.05V typical) by boosting the battery voltage. The IC is available in 30-pin WCSP package.

The bq24140 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates two synchronous PWM chargers, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, the IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to 125°C typical. To support USB OTG device, the IC can provide VBUS (5.05V typical) by boosting the battery voltage. The IC is available in 30-pin WCSP package.
filter Andere Batterielader-ICs suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 2
Typ Titel Datum
* Data sheet 1.5A Dual Input Switchmode Charger with USB-OTG Support datasheet 05 Aug 2011
Application note BQ241xx/BQ246xx Selection of Multi-Cell Standalone Switching Battery Chargers 31 Dez 2019

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Support-Software

SLUC266 — bq24140EVM software

Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware

Produkte
Batterielader-ICs
  • BQ24140 — Switchmode-Lader, 1,5 A, zwei Eingänge, mit USB-OTG-Unterstützung
Herunterladen
Gerberdatei

bq24140EVM-003 gerbers

SLUC296.ZIP (336 KB)
Herunterladen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
DSBGA (YFF) 30 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos