TPS65276V

Name: TPS65276V
Brand: TI
SKU: TPS65276V
Price: 2.06 USD

AKTIV

Synchroner Zweifach-Abwärtswandler, 4,5 bis 18 V Eingangsspannung, 6 A und 3,5 A mit I2C-Steuerung

Jetzt bestellen

Datenblatt

document-pdfAcrobat 4.5V to 18V Input, 6A/3.5A Dual Synchronous Step-Down Converter datasheet (Rev. B) (Englisch)

TPS65276V

AKTIV

Datenblatt

Jetzt bestellen

Produktdetails

Rating

Catalog

Topology

Buck

Iout (max) (A)

6

Vin (max) (V)

18

Vin (min) (V)

4.5

Vout (max) (V)

15

Vout (min) (V)

0.6

Features

Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Enable, Frequency synchronization, Light-load efficiency, Phase Interleaving, Power good, Soft-start adjustable, Synchronous rectification, UVLO adjustable

Control mode

current mode

Switching frequency (min) (kHz)

200

Switching frequency (max) (kHz)

1600

Operating temperature range (°C)

-40 to 125

Iq (typ) (µA)

10000

Duty cycle (max) (%)

95

Type

Converter

Rating

Catalog

Topology

Buck

Iout (max) (A)

6

Vin (max) (V)

18

Vin (min) (V)

4.5

Vout (max) (V)

15

Vout (min) (V)

0.6

Features

Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Enable, Frequency synchronization, Light-load efficiency, Phase Interleaving, Power good, Soft-start adjustable, Synchronous rectification, UVLO adjustable

Control mode

current mode

Switching frequency (min) (kHz)

200

Switching frequency (max) (kHz)

1600

Operating temperature range (°C)

-40 to 125

Iq (typ) (µA)

10000

Duty cycle (max) (%)

95

Type

Converter

HTSSOP (DAP)

32

89.1 mm² 11 x 8.1

VQFN (RHH)

36

36 mm² 6 x 6

4.5-V to 18-V Wide Input Voltage Range
I²C Controlled 7-Bits VID Programmable
Output Voltage from 0.68 V to 1.95 V with 10-mV
Steps for Each Buck; Output Voltage Can Divider
Programmable Slew Rate Control for Output Voltage
Transition
Up to 6-A Maximum Continuous Output Current in
Buck 1 and 3.5-A in Buck 2
I²C Compatible Interface With Standard Mode
(100 kHz) and Fast Mode (400 kHz)
I²C Read Back Power Good Status and
Die Temperature Warning
Pulse Skipping Mode to Achieve High Efficiency
in Light Load
Adjustable Switching Frequency 200 kHz - 1.6 MHz
Set by External Resistor
Dedicated Enable and Soft-Start for Each Buck
Peak Current-Mode Control with Simple Compensation
Circuit
Cycle-by-Cycle Over Current Protection
180° Out-of-Phase Operation to Reduce Input
Capacitance and Power Supply Induced Noise
Over Temperature Protection
Available in 32-Pin Thermally Enhanced HTSSOP (DAP)
and 36-Pin QFN 6-mm x 6-mm (RHH) Packages

4.5-V to 18-V Wide Input Voltage Range
I²C Controlled 7-Bits VID Programmable
Output Voltage from 0.68 V to 1.95 V with 10-mV
Steps for Each Buck; Output Voltage Can Divider
Programmable Slew Rate Control for Output Voltage
Transition
Up to 6-A Maximum Continuous Output Current in
Buck 1 and 3.5-A in Buck 2
I²C Compatible Interface With Standard Mode
(100 kHz) and Fast Mode (400 kHz)
I²C Read Back Power Good Status and
Die Temperature Warning
Pulse Skipping Mode to Achieve High Efficiency
in Light Load
Adjustable Switching Frequency 200 kHz - 1.6 MHz
Set by External Resistor
Dedicated Enable and Soft-Start for Each Buck
Peak Current-Mode Control with Simple Compensation
Circuit
Cycle-by-Cycle Over Current Protection
180° Out-of-Phase Operation to Reduce Input
Capacitance and Power Supply Induced Noise
Over Temperature Protection
Available in 32-Pin Thermally Enhanced HTSSOP (DAP)
and 36-Pin QFN 6-mm x 6-mm (RHH) Packages

TPS65276V is a monolithic dual synchronous buck converter with wide 4.5V to 18V operating input voltage range that encompassed most intermediate bus voltage operating off 5-, 9-, 12- or 15-V power bus or battery. The converter with constant frequency peak current mode control is designed to simplify its application while giving the designers options to optimize their usage according to the target applications.

Each buck converter in TPS65276V has external feedback resistors that can be used for setting the initial start up voltage. The feedback voltage reference for this start-up option is 0.6 V. Once the VID DAC is updated via the I²C, the buck converter switches feedback resistors from external to internal. The output voltage in each buck can be programmable from 0.68 V to 1.95 V in 10-mV steps with I²C Controlled 7-Bits VID.

Each buck converter in TPS65276V can also be I²C controlled for enabling/disabling output voltage, setting the pulse skipping mode and reading the power good status and die temperature warning.

The switching frequency of the converters can be set from 200 kHz to 1.6 MHz with an external resistor. Two converters have clock signal with 180° out-of-phase.

TPS65276V features dedicated enable pin when I²C interface is not used. Independent soft-start pin provides flexibility in power up programmability. Constant frequency peak current mode control simplifies the compensation and provides fast transient response. Cycle-by-cycle over current protection and hiccup mode operation limit MOSFET power dissipation in short circuit or over loading fault conditions. Low side reverse over current protection also prevents excessive sinking current from damaging the converter.

TPS65273V also features a light load pulse skipping mode (PSM) that can be controlled by I²C or MODE pin configuration. The PSM mode allows a power loss reduction on the input power supplied to the system to achieve high efficiency at light loading.

The TPS65273V is available in a 32-pin thermally enhanced HTSSOP (DAP) package and 36-pin QFN 6-mm × 6-mm (RHH) package.

TPS65276V is a monolithic dual synchronous buck converter with wide 4.5V to 18V operating input voltage range that encompassed most intermediate bus voltage operating off 5-, 9-, 12- or 15-V power bus or battery. The converter with constant frequency peak current mode control is designed to simplify its application while giving the designers options to optimize their usage according to the target applications.

Each buck converter in TPS65276V has external feedback resistors that can be used for setting the initial start up voltage. The feedback voltage reference for this start-up option is 0.6 V. Once the VID DAC is updated via the I²C, the buck converter switches feedback resistors from external to internal. The output voltage in each buck can be programmable from 0.68 V to 1.95 V in 10-mV steps with I²C Controlled 7-Bits VID.

Each buck converter in TPS65276V can also be I²C controlled for enabling/disabling output voltage, setting the pulse skipping mode and reading the power good status and die temperature warning.

The switching frequency of the converters can be set from 200 kHz to 1.6 MHz with an external resistor. Two converters have clock signal with 180° out-of-phase.

TPS65276V features dedicated enable pin when I²C interface is not used. Independent soft-start pin provides flexibility in power up programmability. Constant frequency peak current mode control simplifies the compensation and provides fast transient response. Cycle-by-cycle over current protection and hiccup mode operation limit MOSFET power dissipation in short circuit or over loading fault conditions. Low side reverse over current protection also prevents excessive sinking current from damaging the converter.

TPS65273V also features a light load pulse skipping mode (PSM) that can be controlled by I²C or MODE pin configuration. The PSM mode allows a power loss reduction on the input power supplied to the system to achieve high efficiency at light loading.

The TPS65273V is available in a 32-pin thermally enhanced HTSSOP (DAP) package and 36-pin QFN 6-mm × 6-mm (RHH) package.

filter

Andere AC/DC- und DC/DC-Wandler (integrierter FET) suchen

Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star

=Von TI ausgewählte Top-Empfehlungen für dieses Produkt

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.

Alle anzeigen 2

	Typ	Titel		Datum
*	Data sheet	4.5V to 18V Input, 6A/3.5A Dual Synchronous Step-Down Converter datasheet (Rev. B)		16 Jan 2014
	Application note	Measure Power Stage Gain and Slope Compensation in PCM (Peak Current Mode) BUCK (Rev. A)	PDF \| HTML	01 Apr 2019

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.