Inicio Circuitos integrados de gestión de baterías Medidores de carga de baterías
Inicio
Circuitos integrados de gestión de baterías
Medidores de carga de baterías

BQ2018

COMPRA POR ÚLTIMA VEZ

Contador de carga/descarga multiquímica con entrada y salida de 1 cable de alta velocidad (HDQ)

Haga su pedido ahora
Hoja de datos
BQ2018 está en proceso de ser discontinuado
Este producto está en proceso de ser suspendido. Los nuevos diseños deben considerar un producto alternativo.
open-in-new Comparar alternativas
Misma funcionalidad con diferente configuración de pines que el dispositivo comparado
BQ27Z746 ACTIVO Indicador de combustible del lado del paquete de una celda con tecnología Impedance Track™ y protect Integrated protection, SHA-256 authentication, low-voltage (2.0 V) operation, black box recorder
BQ27Z561-R2 ACTIVO Solución para el indicador de gas de batería Impedance Track para paquetes de baterías de iones de l SHA-256 authentication, low-voltage (2.0 V), black box recorder, enhanced charging algorithm

BQ2018

COMPRA POR ÚLTIMA VEZ
Hoja de datos Haga su pedido ahora

Detalles del producto

Cell chemistry Lead Acid, Li-Ion/Li-Polymer, NiCd, NiMH Number of series cells Single Cell Communication interface HDQ Battery capacity (min) (mAh) 1000 Battery capacity (max) (mAh) 4500 Implementation Pack External capacity indication None Features Coulomb Counter Operating temperature range (°C) -20 to 70 Rating Catalog
Cell chemistry Lead Acid, Li-Ion/Li-Polymer, NiCd, NiMH Number of series cells Single Cell Communication interface HDQ Battery capacity (min) (mAh) 1000 Battery capacity (max) (mAh) 4500 Implementation Pack External capacity indication None Features Coulomb Counter Operating temperature range (°C) -20 to 70 Rating Catalog
TSSOP (PW) 8 19.2 mm² (3 mm × 6.4 mm) SOIC (D) 8 29.4 mm² (4.9 mm × 6 mm)
  • Multifunction charge/discharge counter
  • Resolves signals less than 12.5uV
  • Internal offset calibration improves accuracy
  • 1024 bits of NVRAM configured as 128 x 8
  • Internal temperature sensor for self-discharge estimation
  • Single-wire serial interface
  • Dual operating modes:
    - Operating: <80uA
    - Sleep: <10uA
  • REG output for low-cost microregulation
  • Internal timebase eliminates external components
  • 8-pin TSSOP or SOIC allows battery pack integration
  • Multifunction charge/discharge counter
  • Resolves signals less than 12.5uV
  • Internal offset calibration improves accuracy
  • 1024 bits of NVRAM configured as 128 x 8
  • Internal temperature sensor for self-discharge estimation
  • Single-wire serial interface
  • Dual operating modes:
    - Operating: <80uA
    - Sleep: <10uA
  • REG output for low-cost microregulation
  • Internal timebase eliminates external components
  • 8-pin TSSOP or SOIC allows battery pack integration

The bq2018 is a low-cost charge/discharge counter peripheral packaged in an 8-pin TSSOP or SOIC. It works with an intelligent host controller, providing state-of-charge information for rechargeable batteries.

The bq2018 measures the voltage drop across a low-value series sense resistor between the negative terminal of the battery and the battery pack ground contact. By using the accumulated counts in the charge, discharge, and self-discharge registers, an intelligent host controller can determine battery state-of-charge information. To improve accuracy, an offset count register is available. The system host controller is responsible for the register maintenance by resetting the charge in/out and self-discharge registers as needed.

The bq2018 also features 128 bytes of NVRAM registers. The upper 13 bytes of NVRAM contain the capacity monitoring and status information. The RBI input operates from an external power storage source such as a capacitor or a series cell in the battery pack, providing register nonvolatility for periods when the battery is shorted to ground or when the battery charge state is not sufficient to operate the bq2018. During this mode, the register backup current is less than 100nA.

Packaged in an 8-pin TSSOP or SOIC, the bq2018 is small enough to fit in the crevice between two A-size cells or within the width of a prismatic cell.

The bq2018 is a low-cost charge/discharge counter peripheral packaged in an 8-pin TSSOP or SOIC. It works with an intelligent host controller, providing state-of-charge information for rechargeable batteries.

The bq2018 measures the voltage drop across a low-value series sense resistor between the negative terminal of the battery and the battery pack ground contact. By using the accumulated counts in the charge, discharge, and self-discharge registers, an intelligent host controller can determine battery state-of-charge information. To improve accuracy, an offset count register is available. The system host controller is responsible for the register maintenance by resetting the charge in/out and self-discharge registers as needed.

The bq2018 also features 128 bytes of NVRAM registers. The upper 13 bytes of NVRAM contain the capacity monitoring and status information. The RBI input operates from an external power storage source such as a capacitor or a series cell in the battery pack, providing register nonvolatility for periods when the battery is shorted to ground or when the battery charge state is not sufficient to operate the bq2018. During this mode, the register backup current is less than 100nA.

Packaged in an 8-pin TSSOP or SOIC, the bq2018 is small enough to fit in the crevice between two A-size cells or within the width of a prismatic cell.
filter Buscar otro/a Medidores de carga de baterías
Descargar

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 1
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos Power Minder IC datasheet 5/09/1999

Pedidos y calidad