Inicio Controladores para motores Drivers para motores de corriente continua con escobillas (BDC)
Inicio
Controladores para motores
Drivers para motores de corriente continua con escobillas (BDC)
NUEVO

DRV8163-Q1

ACTIVO

Controlador de motor de medio puente de 48 V con diagnóstico y detección de corriente interna para a

Haga su pedido ahora
Hoja de datos

DRV8163-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Number of full bridges 1/2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 36 RDS(ON) (HS + LS) (mΩ) 42 Sleep current (µA) 5 Control mode PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current Regulation, Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Topology Integrated FET Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
Number of full bridges 1/2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 36 RDS(ON) (HS + LS) (mΩ) 42 Sleep current (µA) 5 Control mode PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current Regulation, Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Topology Integrated FET Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
VQFN-HR (VAK) 15 21 mm² 3.5 x 6

  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA

  • Functional Safety-Compliant Targeted

    • Documentation available to aid functional safety system design
  • 4.5V to 65V (70V abs. max) operating range
  • DRV8163-Q1MOSFET ON resistance (HS + LS): 43mΩ
  • Maximum output current = 40A
  • 2 Interface options - HW or SPI
  • PWM frequency operation up to 100kHz with automatic dead time assertion
  • Configurable slew rate and spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated current sense (eliminates shunt resistor)
  • Proportional load current output on IPROPI

  • Die temperature monitoring on IPROPI (SPI only)

  • Configurable current regulation
  • Protection and diagnostic features with configurable fault reaction (latched or retry)
    • Load diagnostics in both the off-state and on-state to detect open load and short circuit
    • Voltage monitoring on supply (VM)
    • Over current protection

    • Over temperature warning (SPI only)

    • Over temperature protection
    • Fault indication on nFAULT pin
  • Supports 1.8V, 3.3V, 5V logic inputs
  • Low sleep current - 7µA typical at 25°C
  • Device family comparison table

  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA

  • Functional Safety-Compliant Targeted

    • Documentation available to aid functional safety system design
  • 4.5V to 65V (70V abs. max) operating range
  • DRV8163-Q1MOSFET ON resistance (HS + LS): 43mΩ
  • Maximum output current = 40A
  • 2 Interface options - HW or SPI
  • PWM frequency operation up to 100kHz with automatic dead time assertion
  • Configurable slew rate and spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated current sense (eliminates shunt resistor)
  • Proportional load current output on IPROPI

  • Die temperature monitoring on IPROPI (SPI only)

  • Configurable current regulation
  • Protection and diagnostic features with configurable fault reaction (latched or retry)
    • Load diagnostics in both the off-state and on-state to detect open load and short circuit
    • Voltage monitoring on supply (VM)
    • Over current protection

    • Over temperature warning (SPI only)

    • Over temperature protection
    • Fault indication on nFAULT pin
  • Supports 1.8V, 3.3V, 5V logic inputs
  • Low sleep current - 7µA typical at 25°C
  • Device family comparison table

The DRV8163-Q1 is a wide-voltage, high-power fully integrated half-bridge driver for 24V and 48V automotive applications. Designed in a BiCMOS high-power process technology node, this device in a power package offers excellent power handling and thermal capability while providing compact package size, ease of layout, EMI control, accurate current sense, robustness, and diagnostic capability.

The device integrates a N-channel half-bridge, charge pump, high-side current sensing with regulation, current proportional output, and protection circuitry. The integrated sensing uses a current mirror, removing the need for shunt resistors, saving board area, and reducing system cost. A low-power sleep mode is provided to achieve low quiescent current.

The device offers voltage monitoring and load diagnostics, as well as protection features against overcurrent and overtemperature. Fault conditions are indicated on the nFAULT pin. The device is available in two variants: HW interface and SPI. The SPI variant offers more flexibility in device configuration and fault observability.

The DRV8163-Q1 is a wide-voltage, high-power fully integrated half-bridge driver for 24V and 48V automotive applications. Designed in a BiCMOS high-power process technology node, this device in a power package offers excellent power handling and thermal capability while providing compact package size, ease of layout, EMI control, accurate current sense, robustness, and diagnostic capability.

The device integrates a N-channel half-bridge, charge pump, high-side current sensing with regulation, current proportional output, and protection circuitry. The integrated sensing uses a current mirror, removing the need for shunt resistors, saving board area, and reducing system cost. A low-power sleep mode is provided to achieve low quiescent current.

The device offers voltage monitoring and load diagnostics, as well as protection features against overcurrent and overtemperature. Fault conditions are indicated on the nFAULT pin. The device is available in two variants: HW interface and SPI. The SPI variant offers more flexibility in device configuration and fault observability.
filter Buscar otro/a Drivers para motores de corriente continua con escobillas (BDC)
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 3
Tipo Título Fecha
* Data sheet DRV8163-Q1 Automotive 65V Half-Bridge Driver with Integrated Current Sense and Diagnostics datasheet (Rev. A) PDF | HTML 03 sep 2025
White paper Software-Defined Vehicles Shift the Future of Automotive Electronics Into Gear (Rev. B) PDF | HTML 21 ene 2025
Application note Calculating Power Dissipation for a H-Bridge or Half Bridge Driver (Rev. A) PDF | HTML 22 jul 2021

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

DRV8163H-Q1EVM — Módulo de evaluación DRV8163-Q1 para variante de hardware

El módulo de evaluación (EVM) DRV8163H-Q1 muestra las características y el rendimiento del paquete HotRod™ DRV8163H. El DRV8163H-Q1 cuenta con un controlador de medio puente totalmente integrado, diseñado para una amplia gama de aplicaciones automotrices. El controlador de medio puente está (...)
Guía del usuario: PDF | HTML
No disponible en TI.com
Placa de evaluación

DRV8163S-Q1EVM — Módulo de evaluación DRV8163-Q1 para variante SPI

El módulo de evaluación (EVM) DRV8163H-Q1 muestra las características y el rendimiento del paquete HotRod™ DRV8163H. El DRV8163H-Q1 cuenta con un controlador de medio puente totalmente integrado, diseñado para una amplia gama de aplicaciones automotrices. El controlador de medio puente está (...)
Guía del usuario: PDF | HTML
No disponible en TI.com
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
VQFN-HR (VAK) 15 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos