Inicio Controladores para motores Drivers para motores paso a paso
Inicio
Controladores para motores
Drivers para motores paso a paso

DRV8462

ACTIVO

Controlador de motor de paso de doble puente H de 65 V y 10 A con sintonización inteligente, detecci

Haga su pedido ahora
Hoja de datos

DRV8462

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Vs ABS (max) (V) 65 Vs (min) (V) 4.5 Peak output current (A) 8 Control mode STEP/DIR Control interface Hardware (GPIO), SPI Number of full bridges 2 Full-scale current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Microstepping levels 256 Decay mode Mixed, Smart Tune Features Current Regulation, Integrated Current Sensing, Open-Load Detection, Smart Tune, Stall Detection Rating Catalog Operating temperature range (°C) -40 to 125
Vs ABS (max) (V) 65 Vs (min) (V) 4.5 Peak output current (A) 8 Control mode STEP/DIR Control interface Hardware (GPIO), SPI Number of full bridges 2 Full-scale current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Microstepping levels 256 Decay mode Mixed, Smart Tune Features Current Regulation, Integrated Current Sensing, Open-Load Detection, Smart Tune, Stall Detection Rating Catalog Operating temperature range (°C) -40 to 125
HTSSOP (DDV) 44 113.4 mm² (14 mm × 8.1 mm) HTSSOP (DDW) 44 113.4 mm² (14 mm × 8.1 mm)
  • Stepper motor driver
    • SPI or H/W interface with STEP/DIR pins
    • Up to 1/256 microstepping indexer

  • 4.5 V to 65 V operating supply voltage range

    • Supports standard 24 V, 36 V and 48 V rails

  • Low R DS(ON): 100 mΩ HS + LS at 24 V, 25°C

  • High current capacity per bridge:
    • DDW Package: 5 A full-scale, 3.5 A RMS
    • DDV Package: 10 A full-scale, 7 A RMS
  • DDW package pin-to-pin compatible with -
  • Integrated current sensing and regulation
    • 5% full-scale current accuracy
  • Smart tune and mixed decay regulation options
  • Silent step decay mode for silent operation at standstill and low speed
  • Automatic Microstepping mode for step frequency interpolation
  • Customizable microstepping indexer table
  • Auto-torque for load dependent current control
  • Standstill Power Saving mode
  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Separate logic supply voltage ( VCC)
  • Protection and diagnostic features
    • Sensorless Stall Detection
    • VM undervoltage lockout (UVLO)
    • Open-load detection (OL)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
    • Indexer zero position output ( nHOME)
  • Stepper motor driver
    • SPI or H/W interface with STEP/DIR pins
    • Up to 1/256 microstepping indexer

  • 4.5 V to 65 V operating supply voltage range

    • Supports standard 24 V, 36 V and 48 V rails

  • Low R DS(ON): 100 mΩ HS + LS at 24 V, 25°C

  • High current capacity per bridge:
    • DDW Package: 5 A full-scale, 3.5 A RMS
    • DDV Package: 10 A full-scale, 7 A RMS
  • DDW package pin-to-pin compatible with -
  • Integrated current sensing and regulation
    • 5% full-scale current accuracy
  • Smart tune and mixed decay regulation options
  • Silent step decay mode for silent operation at standstill and low speed
  • Automatic Microstepping mode for step frequency interpolation
  • Customizable microstepping indexer table
  • Auto-torque for load dependent current control
  • Standstill Power Saving mode
  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Separate logic supply voltage ( VCC)
  • Protection and diagnostic features
    • Sensorless Stall Detection
    • VM undervoltage lockout (UVLO)
    • Open-load detection (OL)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
    • Indexer zero position output ( nHOME)

The DRV8462 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 100 mΩ HS + LS on-resistance allow up to 10-A current.

The auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode provides noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.

The DRV8462 requires minimal tuning to configure the advanced features. The device supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8462 a choice for high-performance stepper systems.

The DRV8462 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 100 mΩ HS + LS on-resistance allow up to 10-A current.

The auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode provides noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.

The DRV8462 requires minimal tuning to configure the advanced features. The device supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8462 a choice for high-performance stepper systems.
filter Buscar otro/a Drivers para motores paso a paso
Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new Comparar alternativas
Reemplazo con funcionalidad mejorada del dispositivo comparado
DRV8452 ACTIVO Controlador de motor paso a paso de doble puente en H, 50 V, 5 A, con ajuste inteligente, detección P2P device for lower voltage applications (50 V abs max)
DRV8461 ACTIVO Controlador de motor paso a paso de doble puente en H, 65 V, 3 A, con ajuste inteligente, detección 65-V P2P device for lower current applications (3A FS)
Funcionalidad similar a la del dispositivo comparado
DRV8434A ACTIVO Controlador de motor bipolar de paso de 48 V y 2.5 A, detección de corriente y de calado integrados Stepper driver with stall detection for lower voltage applications
DRV8262 ACTIVO Controlador de motor de puente en H simple o doble de 65 V con detección y regulación de corriente i Single or dual H-bridge motor driver with  PH/EN or PWM interface
DRV8962 ACTIVO Controlador de medio puente de 65 V y cuatro canales con salidas de detección de corriente Stepper driver for higher voltage and higher current applications (65 V abs max, 5 A FS)

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 6
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos DRV8462: 65 V, 5-10 A Stepper Motor Driver for High Efficiency and Noiseless Operation datasheet (Rev. B) PDF | HTML 28/09/2023
Nota sobre la aplicación System Efficiency Improvement With the DRV8452 and DRV8462 PDF | HTML 19/01/2023
Guía del usuario DRV84xx_DRV82x2_DRV89x2-EVM User's Guide (Rev. B) PDF | HTML 18/01/2023
Certificado DRV8462EVM EU RoHS Declaration of Conformity (DoC) (Rev. A) 17/01/2023
Nota sobre la aplicación Integrated FETs vs External FETs: Performance Comparison of Motor Drivers PDF | HTML 22/12/2022
Certificado DRV8462VEVM EU RoHS Declaration of Conformity (DoC) 16/12/2022

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

DRV8462EVM — Módulo de evaluación DRV8462 para controlador de motor paso a paso con micropaso automático

El módulo de evaluación DRV8462EVM muestra las características y el rendimiento del DRV8462DDWR.

El DRV8462 es un controlador de motor a pasos totalmente integrado para aplicaciones industriales. El dispositivo funciona en un rango de alimentación de 4.5 V a 65 V y es capaz de conducir hasta 5 A de (...)

Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Soporte de software

DRV84XX-DRV89X2-DRV82X2-EVM-SOFTWARE — EVM GUI and device firmware for DRV84XX_DRV89X2_DRV82X2 family

Zipped folder containing manifests and installers for both the GUI and the firmware of the DRV84XX_DRV89X2_DRV82X2 family of devices. Detailed instructions on how to use the GUI can be found in the User's Guide of the DRV84XX-DRV89X2-DRV82X2-EVM.
Productos y hardware compatibles
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
HTSSOP (DDV) 44 Ultra Librarian
HTSSOP (DDW) 44 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos