Inicio Lógica y traducción de voltaje Traductores de tensión y desplazadores de nivel Traductores de tensión de dirección automática
Inicio
Lógica y traducción de voltaje
Traductores de tensión y desplazadores de nivel
Traductores de tensión de dirección automática

LSF0204-Q1

ACTIVO

Repetidor de nivel multivoltaje bidireccional de 4 bits para interfaz de señales Open-Drain o Push-P

Haga su pedido ahora
Hoja de datos

LSF0204-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Technology family LSF Applications I2C, MDIO, SMBus Bits (#) 4 Data rate (max) (Mbps) 100 High input voltage (min) (V) 0.9 High input voltage (max) (V) 5.5 Vout (min) (V) 0.9 Vout (max) (V) 5.5 IOH (max) (mA) 0 IOL (max) (mA) 0 Supply current (max) (µA) 0.01 Features Output enable Input type Transmission Gate Output type 3-State, Transmission Gate Rating Automotive Operating temperature range (°C) -40 to 125
Technology family LSF Applications I2C, MDIO, SMBus Bits (#) 4 Data rate (max) (Mbps) 100 High input voltage (min) (V) 0.9 High input voltage (max) (V) 5.5 Vout (min) (V) 0.9 Vout (max) (V) 5.5 IOH (max) (mA) 0 IOL (max) (mA) 0 Supply current (max) (µA) 0.01 Features Output enable Input type Transmission Gate Output type 3-State, Transmission Gate Rating Automotive Operating temperature range (°C) -40 to 125
TSSOP (PW) 14 32 mm² 5 x 6.4
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C ≤ TA ≤ 125°C
    • Device HBM ESD classification level 2
    • CDM ESD classification level C6
  • Provides auto-bidirectional voltage translation without direction pin
  • Supports open drain or push-pull applications such as I2C, I2S, SPI, UART, JTAG, MDIO, SDIO, and GPIO
  • Supports up to 100-MHz up translation and greater than 100-MHz down translation at ≤ 30-pF capacitor load and up to 40-MHz up/down translation at 50-pF capacitor load
  • Supports Ioff, partial power down mode (see Section 7.3)
  • Allows bidirectional voltage level translation between
    • 0.95 V ↔ 1.8, 2.5, 3.3, 5.5 V
    • 1.2 V ↔ 1.8, 2.5, 3.3, 5.5 V
    • 1.8 V ↔ 2.5, 3.3, 5.5 V
    • 2.5 V ↔ 3.3, 5.5 V
    • 3.3 V ↔ 5.5 V
  • 5-V tolerance on I/O ports
  • Low Ron enables better signal integrity
  • Flow-through pinout for easy PCB trace routing
  • Latch-up performance exceeds 100 mA per JESD17
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C ≤ TA ≤ 125°C
    • Device HBM ESD classification level 2
    • CDM ESD classification level C6
  • Provides auto-bidirectional voltage translation without direction pin
  • Supports open drain or push-pull applications such as I2C, I2S, SPI, UART, JTAG, MDIO, SDIO, and GPIO
  • Supports up to 100-MHz up translation and greater than 100-MHz down translation at ≤ 30-pF capacitor load and up to 40-MHz up/down translation at 50-pF capacitor load
  • Supports Ioff, partial power down mode (see Section 7.3)
  • Allows bidirectional voltage level translation between
    • 0.95 V ↔ 1.8, 2.5, 3.3, 5.5 V
    • 1.2 V ↔ 1.8, 2.5, 3.3, 5.5 V
    • 1.8 V ↔ 2.5, 3.3, 5.5 V
    • 2.5 V ↔ 3.3, 5.5 V
    • 3.3 V ↔ 5.5 V
  • 5-V tolerance on I/O ports
  • Low Ron enables better signal integrity
  • Flow-through pinout for easy PCB trace routing
  • Latch-up performance exceeds 100 mA per JESD17

The LSF0204-Q1 is automotive qualified four channel auto bidirectional voltage translator that operate from 0.8 V to 4.5 V (Vref_A) and 1.8 V to 5.5 V (Vref_B). This range allows for bidirectional voltage translations between 0.8 V and 5.5 V without the need for a direction pin.

When the An or Bn port is LOW, the switch is in the ON-state and a low resistance connection exists between the An and Bn ports. The low Ron of the switch allows connections to be made with minimal propagation delay and minimal signal distortion. The voltage on the A or B side will be limited to Vref_A and can be pulled up to any level between Vref_A and 5.5 V

The supply voltage (VPUn) for each channel may be individually set up with a pull up resistor. For example, CH1 may be used in up-translation mode (1.2 V ↔ 3.3 V) and CH2 in down-translation mode (2.5 V ↔ 1.8 V).

When EN is HIGH, the translator switch is on, and the An I/O is connected to the Bn I/O, respectively, allowing bidirectional data flow between ports. When EN is LOW, the translator switch is off, and a high-impedance state exists between ports. The EN input circuit is designed to be supplied by Vref_A. EN must be LOW to ensure the high-impedance state during power-up or power-down.

The LSF0204-Q1 is automotive qualified four channel auto bidirectional voltage translator that operate from 0.8 V to 4.5 V (Vref_A) and 1.8 V to 5.5 V (Vref_B). This range allows for bidirectional voltage translations between 0.8 V and 5.5 V without the need for a direction pin.

When the An or Bn port is LOW, the switch is in the ON-state and a low resistance connection exists between the An and Bn ports. The low Ron of the switch allows connections to be made with minimal propagation delay and minimal signal distortion. The voltage on the A or B side will be limited to Vref_A and can be pulled up to any level between Vref_A and 5.5 V

The supply voltage (VPUn) for each channel may be individually set up with a pull up resistor. For example, CH1 may be used in up-translation mode (1.2 V ↔ 3.3 V) and CH2 in down-translation mode (2.5 V ↔ 1.8 V).

When EN is HIGH, the translator switch is on, and the An I/O is connected to the Bn I/O, respectively, allowing bidirectional data flow between ports. When EN is LOW, the translator switch is off, and a high-impedance state exists between ports. The EN input circuit is designed to be supplied by Vref_A. EN must be LOW to ensure the high-impedance state during power-up or power-down.
open-in-new Buscar otro/a Traductores de tensión de dirección automática
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 2
Tipo Título Fecha
* Data sheet LSF0204-Q1 Automotive Qualified 4-Bit Auto-Bidirectional Multi-Voltage Level Translator datasheet (Rev. B) PDF | HTML 29 abr 2021
Selection guide Voltage Translation Buying Guide (Rev. A) 15 abr 2021

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

14-24-LOGIC-EVM — Módulo de evaluación genérico de productos lógicos para encapsulados D, DB, DGV, DW, DYY, NS y PW de

El módulo de evaluación 14-24-LOGIC-EVM (EVM) está diseñado para admitir cualquier dispositivo lógico que esté en un encapsulado D, DW, DB, NS, PW, DYY o DGV de 14 a 24 pines.

Guía del usuario: PDF | HTML
No disponible en TI.com
Placa de evaluación

LSF-EVM — Módulo de evaluación de la familia de repetidores LSF de 1 a 8 bits

The LSF family of devices are level translators that support a voltage range of 0.95V and 5V and provide multi-voltage bidirectional translation without a direction pin.

The LSF-EVM comes populated with the LSF0108PWR device and has landing patterns that are compatible with the LSF0101DRYR, (...)

Guía del usuario: PDF
No disponible en TI.com
Modelo de simulación

LSF0204 HSPICE Model

SLVMAL3.ZIP (7 KB) - HSpice Model
Descargar
Paquete Pasadores Descargar
TSSOP (PW) 14 Ver opciones
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos