この製品には新バージョンがあります。
比較対象デバイスと同等の機能で、ピン配置が異なる製品
BQ2018
- Multifunction charge/discharge counter
- Resolves signals less than 12.5uV
- Internal offset calibration improves accuracy
- 1024 bits of NVRAM configured as 128 x 8
- Internal temperature sensor for self-discharge estimation
- Single-wire serial interface
- Dual operating modes:
- Operating: <80uA
- Sleep: <10uA - REG output for low-cost microregulation
- Internal timebase eliminates external components
- 8-pin TSSOP or SOIC allows battery pack integration
The bq2018 is a low-cost charge/discharge counter peripheral packaged in an 8-pin TSSOP or SOIC. It works with an intelligent host controller, providing state-of-charge information for rechargeable batteries.
The bq2018 measures the voltage drop across a low-value series sense resistor between the negative terminal of the battery and the battery pack ground contact. By using the accumulated counts in the charge, discharge, and self-discharge registers, an intelligent host controller can determine battery state-of-charge information. To improve accuracy, an offset count register is available. The system host controller is responsible for the register maintenance by resetting the charge in/out and self-discharge registers as needed.
The bq2018 also features 128 bytes of NVRAM registers. The upper 13 bytes of NVRAM contain the capacity monitoring and status information. The RBI input operates from an external power storage source such as a capacitor or a series cell in the battery pack, providing register nonvolatility for periods when the battery is shorted to ground or when the battery charge state is not sufficient to operate the bq2018. During this mode, the register backup current is less than 100nA.
Packaged in an 8-pin TSSOP or SOIC, the bq2018 is small enough to fit in the crevice between two A-size cells or within the width of a prismatic cell.
技術資料
種類 | タイトル | 最新の英語版をダウンロード | 日付 | |||
---|---|---|---|---|---|---|
* | データシート | Power Minder | 1999年 9月 5日 | |||
アプリケーション・ノート | Gas Gauging Basics Using TI Battery Monitor ICs (Rev. A) | 2003年 10月 17日 | ||||
アプリケーション・ノート | Advanced Gas Gauge Firmware Flowchart for TI Battery Monitor ICs | 2002年 8月 28日 | ||||
アプリケーション・ノート | Advanced Gas Gauge Host Firmware for TI Battery Monitor ICs | 2001年 5月 16日 | ||||
アプリケーション・ノート | HDQ Communication Basics for TI Battery Monitor ICs | 2001年 5月 16日 | ||||
ユーザー・ガイド | bq2018 EVM | 2000年 4月 10日 | ||||
ユーザー・ガイド | bq2018 Power Minder | 2000年 4月 10日 | ||||
ユーザー・ガイド | DM2382 Gas Gauge Peripheral and Li-Ion Pack Protection Demo Board | 1999年 9月 5日 | ||||
アプリケーション・ノート | Designed to Go: Universal Battery Monitor Using the bq2018 Power Minder IC | 1999年 9月 5日 | ||||
ユーザー・ガイド | EV2200-18 Evaluation System User Guide | 1999年 9月 5日 |
設計と開発
その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。
パッケージ | ピン数 | ダウンロード |
---|---|---|
SOIC (D) | 8 | オプションの表示 |
TSSOP (PW) | 8 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL 定格 / ピーク リフロー
- MTBF/FIT 推定値
- 材質成分
- 認定試験結果
- 継続的な信頼性モニタ試験結果
- ファブの拠点
- 組み立てを実施した拠点