AFE5816
- 16-channel, AFE for ultrasound applications:
- Input attenuator, LNA, LPF, ADC, and CW mixer
- Optimized signal chains for TGC and CW modes
- Digital time gain compensation (DTGC)
- Total gain range: 6dB to 45dB
- Linear input range: 1VPP
- Input attenuator with DTGC:
- 8dB to 0dB attenuation with 0.125dB step
- Supports matched impedance for:
- 50Ω to 800Ω source impedance
- Low-noise amplifier (LNA) with DTGC:
- 14dB to 45dB gain with 0.125dB step
- Low input current noise: 1.2pA/√ Hz
- 3rd-order, linear-phase, low-pass filter (LPF):
- 10MHz, 15MHz, 20MHz, and 25MHz
- Analog-to-digital converter (ADC) with programmable resolution:
- 14-bit ADC: 75dBFS idle channel SNR at 65 MSPS
- 12-bit ADC: 72dBFS idle channel SNR at 80 MSPS
- LVDS interface with a maximum speed up to 1GBPS
- Optimized for noise and power:
- 90mW/Ch at 1nV/√ Hz, 65 MSPS, TGC mode
- 55mW/Ch at 1.45nV/√ Hz, 40 MSPS, TGC mode
- 59mW/Ch, CW mode
- Excellent device-to-device gain matching:
- ±0.5dB (typical)
- Low harmonic distortion: –60dBc level
- Fast and consistent overload recovery
- Continuous wave (CW) path with:
- Passive mixer
- Low close-in phase noise of –148dBc/Hz at 1kHz frequency
- Phase resolution: λ / 16
- Supports 16X, 8X, 4X, and 1X CW clocks
- 12dB suppression of 3rd and 5th harmonics
- Small package: 15mm × 15mm NFBGA-289
The AFE5816 is a highly-integrated, analog front-end (AFE) solution specifically designed for ultrasound systems where high performance, low power, and small size are required.
The AFE5816 is an integrated analog front-end (AFE) optimized for medical ultrasound application. The AFE5816 is a multichip module (MCM) device with two dies: VCA and ADC_CONV. Each die has total of 16 channels.
Each channel in the VCA die can be configured in two modes: time gain compensation (TGC) mode and continuous wave (CW) mode. In TGC mode, each channel includes an input attenuator (ATTEN), a low-noise amplifier (LNA) with variable-gain, and a third-order, low-pass filter (LPF). The attenuator supports an attenuation range of 8dB to 0dB, and the LNA supports gain ranges from 14dB to 45dB. The LPF cutoff frequency can be configured at 10MHz, 15MHz, 20MHz, or 25MHz to support ultrasound applications with different frequencies. In CW mode, each channel includes an LNA with a fixed gain of 18dB, and a low-power passive mixer with 16 selectable phase delays. Different phase delays can be applied to each analog input signal to perform an on-chip beamforming operation. A harmonic filter in the CW mixer suppresses the third and fifth harmonic to enhance the sensitivity of the CW Doppler measurement. CW mode supports three clock modes: 16X, 8X, and 4X.
Each channel of the ADC_CONV die has a high-performance analog-to-digital converter (ADC) with a programmable resolution of 14 bits or 12 bits. The ADC achieves 75dBFS signal-to-noise ratio (SNR) in 14-bit mode, and 72dBFS SNR in 12-bit mode. This ADC provides excellent SNR at low-channel gain. The devices operate at maximum speeds of 65 MSPS and 80 MSPS, providing 14-bit and 12-bit output, respectively. The ADC is designed to scale power with sampling rate. The output interface of the ADC is a low-voltage differential signaling (LVDS) interface that can easily interface with low-cost field-programmable gate arrays (FPGAs).
The AFE5816 also allows various power and noise combinations to be selected for optimizing system performance. Therefore, these devices are suitable ultrasound AFE solutions for systems with strict battery-life requirements. The AFE5816 is available in a 15mm × 15mm NFBGA-289 package (ZAV package, S-PBGA-N289) and is specified for operation from –40°C to +85°C. The device is also pin-to-pin compatible with the AFE5818 family.
추가 정보 요청
전체 데이터시트 및 기타 설계 리소스는 NDA에 따라 제공됩니다. 지금 신청
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | AFE5816 16-Channel Ultrasound AFE With 90mW/Channel Power, 1nV/√ Hz Noise, 14-Bit, 65-MSPS or 12-Bit, 80 MSPS ADC and Passive CW Mixer datasheet | PDF | HTML | 2024/03/01 |
| Application note | Precision Sum Circuit Support Hi Output Current Multiple AFEs in Ultasound App | 2017/11/20 | ||
| Application note | Introduction to Ultrasound | 2017/07/10 | ||
| Application note | Time Gain Control (Compensation) in Ultrasound Applications | 2016/12/02 | ||
| EVM User's guide | AFE5816 EVM User Guide (Rev. A) | 2016/02/17 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AFE5816EVM — AFE5816 평가 모듈
The AFE5816EVM is a highly integrated Analog Front-End (AFE) solution specifically designed for ultrasound systems in which high performance and small size are required. The AFE5816EVM integrates a complete time-gain-control (TGC) imaging path and a continuous wave Doppler (CWD) path. It also (...)
AFE58JD16EVM — AFE58JD16 평가 모듈
AFE58JD16 평가 모듈(EVM)은 뛰어난 성능과 작은 크기가 필요한 초음파 시스템을 위해 특별히 설계된 고집적 아날로그 프론트 엔드(AFE) 솔루션입니다. AFE58JD16EVM은 완전한 타임 게인 제어(TGC) 영상 경로와 연속파 도플러(CWD) 경로를 통합하였습니다. 또한, 시스템 성능을 최적화하기 위해 다양한 전원/잡음 조합 중 하나를 선택할 수 있는 기능이 포함되어 있습니다. AFE58JD16EVM은 하이엔드 시스템뿐 아니라 휴대용 시스템에 적합한 초음파 AFE 솔루션입니다.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| NFBGA (ZAV) | 289 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.