MCF8315C
- Three-phase BLDC motor driver with integrated sensorless motor control algorithm
- Code-free Field Oriented Control (FOC)
- Offline motor parameters measurement with Motor Parameter Extraction Tool (MPET)
- 5-point configurable speed profile support
- Windmilling support through forward resynchronization and reverse drive
- Analog, PWM, freq. or I2C based speed input
- Configurable motor start-up and stop options
- Anti-voltage surge (AVS) protection
- Improved acoustic performance with automatic dead time compensation
- Variable monitoring through DACOUT pin
- 4.5 to 35V operating voltage (40V abs max)
- High (peak) output current capability: 4A (RRY), 3.5A (PWP)
- Low MOSFET on-state resistance
- RRY: RDS(ON)(H+L) at TJ=25°C: 250mΩ(typ.)
- PWP: RDS(ON)(H+L) at TJ=25°C: 265mΩ(typ.)
- Low power sleep mode: Refer
- 5µA (maximum) at VVM = 24V, TA = 25°C
- Speed loop accuracy: 3% with internal clock and 1% with external clock reference
- Customer-configurable non-volatile memory (EEPROM) to store device configuration
- Supports up to 60-kHz PWM frequency for low inductance motor support
- Does not require external current sense resistors; uses built-in current sensing
- Built-in 3.3V, 20mA LDO regulator
- Built-in 3.3V/5V, 170mA buck regulator
- Dedicated DRVOFF pin to disable (Hi-Z) outputs
- Spread spectrum and slew rate for EMI mitigation
- A suite of integrated protection features
- Supply under voltage lockout (UVLO)
- Supply over voltage protection (OVP)
- Motor lock detection (5 different types)
- Over current protection (OCP)
- Thermal warning and shutdown (OTW/TSD)
- Fault condition indication pin (nFAULT)
- Optional fault diagnostics over I2C interface
The MCF8315C provides a single-chip, code-free sensorless FOC solution for customers driving speed-controlled 12 to 24V brushless-DC motors (BLDC) or Permanent Magnet Synchronous motor (PMSM) up to 4A peak current. The MCF8315C integrates three ½-bridges with 40V absolute maximum capability and a low RDS(ON) of 250/265mΩ (high-side + low-side FETs). MCF8315C integrates power management circuits including a voltage-adjustable buck regulator (3.3V/5V, 170mA) and LDO (3.3V/20mA) that can be used to power external circuits.
The FOC algorithm configuration can be stored in non-volatile EEPROM, which allows the device to operate stand-alone once it has been configured. The device receives a speed command through a PWM input, analog voltage, variable frequency square wave or I2C command. There are a large number of protection features integrated into the MCF8315C, intended to protect the device, motor, and system against fault events.
MCF8315C is available in two packages: 32-pin 6x4mm wettable-flank QFN (RRY) and 24-pin 7.8x6.4mm HTSSOP (PWP).
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
MCF8315EVM — MCF8315 3상 무센서 FOC 일체형 MOSFET BLDC 모터 드라이버용 평가 모듈
MCF8315에는 4.5V~35V, 5A 피크 전류 드라이브를 위한 3상 BLDC(브러시리스 DC) 모터의 무센서 FOC 제어를 위한 3개의 하프 H 브리지 통합 MOSFET 드라이버가 있습니다. MCx8315은는 프로그래밍 가능한 조정 전원에 200mA를 지원할 수 있는 벅 레귤레이터를 통합합니다.
이 EVM에는 Motor Studio(MOTORSTUDIO) GUI와 상호 작용하는 데 사용되는 온보드 MSP430(MSP430FR2355)이 포함되어 있습니다.
MCF8315PWPEVM — 24핀 플라스틱 소형 아웃라인 패키지(PWP)용 MCF8315 평가 모듈
MCF8315RRYEVM — 32핀 WQFN(RRY) 패키지용 MCF8315 평가 모듈
MCF8315 평가 모듈(EVM)을 사용하면 32핀 WQFN(RRY) 패키지에서 MCF8315 모터 드라이버의 성능을 평가할 수 있습니다. EVM 에는 마이크로 USB 커넥터에서 UART로 USB 통신을 변환하는 온보드 FTDI 칩이 포함되어 있습니다. 온보드 MSP430FR2355 마이크로컨트롤러(MCU)는 UART 통신을 제어 신호로 변환하며, 이는 MCF8315 장치로 전송됩니다. MCF8315 IC의 다양한 기능 및 구성 가능한 장치별 설정을 평가하는 데 도움이 되는 여러 사용자 선택 가능한 점퍼, 저항, 커넥터 및 테스트 (...)
MOTORSTUDIO — Motor Studio GUI for tuning and evaluating BLDC motor drivers
Motor Studio는 브러시리스 DC(BLDC) 모터 드라이버의 튜닝 프로세스를 단순화하고 장치 평가 및 제품 개발 시간을 줄여주는 간편한 그래픽 사용자 인터페이스(GUI)입니다. GUI는 사용자가 빠르게 모터를 회전시키고 다양한 모터 작동 단계를 최적화하여 최고의 모터 성능, 안정적인 모터 시동 및 최소 잡음을 달성할 수 있게 해줍니다.
BLDC-MCF831XC-TO-MCF831XD-CONVERSION-CALC — Register Map conversion tool - from MCF831xC to MCF831xD
BLDC-MOSFET-THERMAL-CALC — BLDC integrated MOSFET driver thermal calculator tool
TIDA-010951 — 85~265VAC, 0.92PF 단상 PFC를 지원하는 24V, 35W 무센서 FOC BLDC 레퍼런스 설계
에너지 효율을 달성하기 위해 천장 팬과 환기 팬은 간단한 AC 인덕션 모터에서 브러시리스 DC(BLDC) 모터로 이동하고 있습니다. 이 레퍼런스 설계는 단상 전력 역률 보정 절연 플라이백과 85~265VAC 범용 주 전원 공급 입력을 사용하여 오프라인 전압을 변환하고 24VDC에서 최대 0.92pF에 도달할 수 있어 더 높은 효율성 및 역률 문제를 해결합니다. 이 설계는 또한 센서리스 자속 기준 제어(FOC) 브러시리스 모터 제어를 위한 완전 통합되고 보호 성능이 뛰어난 단일 칩을 결합했습니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (PWP) | 24 | Ultra Librarian |
| WQFN (RRY) | 32 | Ultra Librarian |