TS3USB3000
- VCC Range 2.3 V to 4.8 V
- Mobile Hi-Definition Link (MHL) Switch:
- Bandwidth (–3 dB): 6.1 GHz
- RON (Typical): 5.7 Ω
- CON (Typical): 1.6 pF
- USB Switch:
- Bandwidth (–3 dB): 6.1 GHz
- RON (Typical): 4.6 Ω
- CON (Typical): 1.4 pF
- Current Consumption: 30 µA (Typical)
- Special Features:
- IOFF Protection Prevents Current Leakage in Powered-Down State (VCC and VBUS = 0 V)
- 1.8-V Compatible Control Inputs (SEL, OE)
- Overvoltage Tolerance (OVT) on all I/O Pins up to 5.5 V Without External Components
- Overvoltage Protection When 9-V Short to
D+/-Pin
- ESD Performance:
- 3.5-kV Human Body Model (A114B, Class II)
- 1-kV Charged-Device Model (C101)
- 10-Pin UQFN Package
(1.5-mm × 2-mm, 0.5-mm Pitch)
The TS3USB3000 device is a double-pole, double throw (DPDT) multiplexer that includes a high-speed Mobile High-Definition Link (MHL) switch and an USB 2.0 High-Speed (480 Mbps) switch in the same package. These configurations allow the system designer to use a common USB or Micro-USB connector for both MHL video signals and USB data.
The TS3USB3000 has a VCC range of 2.3 V to 4.8 V and supports overvoltage tolerance (OVT) feature, which allows the I/O pins to withstand overvoltage conditions (up to 5.5 V). The power-off protection feature forces all I/O pins to be in high-impedance mode when power is not present, allowing full isolation of the signal lines under such condition without excessive leakage current. The select pins of TS3USB3000 are compatible with 1.8-V control voltage, allowing them to be directly interfaced with the General-Purpose I/O (GPIO) from a mobile processor.
The TS3USB3000 comes with a small 10-pin UQFN package with only 1.5 mm × 2 mm in size, which makes it a perfect candidate to be used in mobile applications.
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TS3USB3000 DPDT USB 2.0 High-Speed and Mobile High-Definition Link (MHL) 6.1-GHz Switch datasheet (Rev. F) | PDF | HTML | 2019/06/10 |
| Application note | Passive Mux Selection Based On Bandwidth > Ron | 2019/09/11 | ||
| Application note | High-Speed Layout Guidelines for Signal Conditioners and USB Hubs | 2018/06/14 | ||
| Technical article | How to protect your EPOS processor from short-circuits in 9-V USB charging | PDF | HTML | 2016/04/21 | |
| Technical article | Protect your application processors from short circuit at 9V | PDF | HTML | 2016/02/23 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| UQFN (RSE) | 10 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.