產品詳細資料

Cell chemistry Li-Ion/Li-Polymer, LiFePO4, NCM Number of series cells Single Cell Communication interface I2C Battery capacity (min) (mAh) 100 Battery capacity (max) (mAh) 32000 Implementation Pack External capacity indication None Features Configurable current limiter, Dynamic Z-Track™ technology, ECC authentication, Integrated Protector, SHA-256 Authentication Operating temperature range (°C) -40 to 85 Rating Catalog
Cell chemistry Li-Ion/Li-Polymer, LiFePO4, NCM Number of series cells Single Cell Communication interface I2C Battery capacity (min) (mAh) 100 Battery capacity (max) (mAh) 32000 Implementation Pack External capacity indication None Features Configurable current limiter, Dynamic Z-Track™ technology, ECC authentication, Integrated Protector, SHA-256 Authentication Operating temperature range (°C) -40 to 85 Rating Catalog
DSBGA (YAH) 15 5.4488 mm² (2.78 mm × 1.96 mm)
  • Fully integrated battery fuel gauge, linear battery charger, protector, and authenticator
  • Battery chemistries supported include Li-ion with LCO, NMC, or LFP cathodes
  • Battery fuel gauging based on patented Dynamic Z-Track technology
    • Automatically adjusts for aging, temperature, and rate-induced effects on the battery
  • Fully featured battery linear charger
    • CC/CV charging up to 2A with JEITA-compliant integrated Advanced Charge Algorithm (ACA)
    • Dynamic Power Path Management
      • MINSYS mode to ensure system voltage does not drop below target threshold while charging with a weak input
      • SUPPLEMENT mode with ultra fast switching time to ensure system does not brown out during loads while charging
    • Ideal diode (ID) mode during discharge to prevent voltage drop to system load
    • PACK+ terminal voltage tolerance of +24V with 1kΩ RPACK value
  • High-accuracy analog front end with two independent ADCs:
    • 18-bit low offset delta-sigma ADC for Coulomb counting with ±100mV input range
    • 16-bit delta-sigma ADC for cell voltage and internal and external temperature sensors
  • Programmable safety and protection:
    • Hardware-level protections
      • Over Voltage Protection (OVP)
      • Under Voltage Protection (UVP)
      • Over Current Charging (OCC)
      • Over Current Discharging (OCD)
      • Short Circuit Discharging (SCD)
    • Firmware-level protections
      • OVP, UVP, OCC, and OCD
      • Under Temperature (UT)
      • Over Temperature (OT)
      • FET Failure (FETF)
      • Charge Timeout (CTO)
  • ECC ECDSA authentication support with secure memory
  • True zero-volt charging to support dead battery charging
  • Integrated RTC with calendar and time of day
  • Ultra-compact, 15-ball DSBGA package (YAH)
  • Fully integrated battery fuel gauge, linear battery charger, protector, and authenticator
  • Battery chemistries supported include Li-ion with LCO, NMC, or LFP cathodes
  • Battery fuel gauging based on patented Dynamic Z-Track technology
    • Automatically adjusts for aging, temperature, and rate-induced effects on the battery
  • Fully featured battery linear charger
    • CC/CV charging up to 2A with JEITA-compliant integrated Advanced Charge Algorithm (ACA)
    • Dynamic Power Path Management
      • MINSYS mode to ensure system voltage does not drop below target threshold while charging with a weak input
      • SUPPLEMENT mode with ultra fast switching time to ensure system does not brown out during loads while charging
    • Ideal diode (ID) mode during discharge to prevent voltage drop to system load
    • PACK+ terminal voltage tolerance of +24V with 1kΩ RPACK value
  • High-accuracy analog front end with two independent ADCs:
    • 18-bit low offset delta-sigma ADC for Coulomb counting with ±100mV input range
    • 16-bit delta-sigma ADC for cell voltage and internal and external temperature sensors
  • Programmable safety and protection:
    • Hardware-level protections
      • Over Voltage Protection (OVP)
      • Under Voltage Protection (UVP)
      • Over Current Charging (OCC)
      • Over Current Discharging (OCD)
      • Short Circuit Discharging (SCD)
    • Firmware-level protections
      • OVP, UVP, OCC, and OCD
      • Under Temperature (UT)
      • Over Temperature (OT)
      • FET Failure (FETF)
      • Charge Timeout (CTO)
  • ECC ECDSA authentication support with secure memory
  • True zero-volt charging to support dead battery charging
  • Integrated RTC with calendar and time of day
  • Ultra-compact, 15-ball DSBGA package (YAH)

The Texas Instruments BQ27Z855 Dynamic Z-Trackgas gauge solution is a fully integrated, accurate 1-series cell gas gauge, JEITA-compliant linear battery charger, protection, and authentication solution.

The BQ27Z855 gas gauge communicates through an I2C compatible interface and combines an ultra-low power ARM M0 RISC processor, high accuracy analog measurement capabilities, integrated flash memory, high-side NMOS FET drivers, and ECC ECDSA authentication to provide a complete, high-performance battery management solution.

The Texas Instruments BQ27Z855 Dynamic Z-Trackgas gauge solution is a fully integrated, accurate 1-series cell gas gauge, JEITA-compliant linear battery charger, protection, and authentication solution.

The BQ27Z855 gas gauge communicates through an I2C compatible interface and combines an ultra-low power ARM M0 RISC processor, high accuracy analog measurement capabilities, integrated flash memory, high-side NMOS FET drivers, and ECC ECDSA authentication to provide a complete, high-performance battery management solution.

下載 觀看有字幕稿的影片 影片

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

BQ27Z855EVM — BQ27Z855 評估模組

BQ27Z855 評估模組 (EVM) 是一款系統級電路板,旨在讓使用者能夠評估其係統中 BQ27Z855 油量計的功能。BQ27Z855 EVM 適用於電池組為 1-S 電池芯,即單顆串聯電池芯的應用。EVM 包括 BQ27Z855 電池電量計、低壓側電流偵測電阻器、整合式高壓側保護器、ENAB 喚醒按鈕、充電器喚醒按鈕、線性電池充電器以及其他接頭選項,以便進行一些修改以滿足預期應用需求。

使用指南: PDF | HTML
支援產品和硬體
有庫存
限制:
??asset.out-of-stock-ti_zh_TW??
無法提供
應用軟體及架構

BQSTUDIO-TEST — Battery Management Studio (bqStudio) Software – Beta version downloads

Battery Management Studio (bqStudio) 提供全套的強固工具,可協助評估、設計、配置、測試或使用 TI 電池管理產品的程序。其中包括可提供暫存器及資料記憶體完整存取的功能,包括支援即時觀看、繪圖和記錄、傳送命令的簡易介面、直接低階通訊和 I/O,以及用於配置、校準和執行學習週期的自動化和引導支援,進而產生實用的檔案,以利裝置投入生產。

在 bqStudio 中也支援舊產品,如 bq20xxx 和 bq30xxx。從適當的產品頁面下載特定的評估軟體。此外,您為 bqStudio 下載的最新化學更新程式需要 bqStudio 的更新版。

支援產品和硬體
韌體

BQ27Z855-FW — BQ27Z855 device firmware

支援產品和硬體
開發模組 (EVM) 的 GUI

BQSTUDIO-GUI — Battery Management Studio (bqStudio) Software - Web Based Version

Battery Management Studio (bqStudio) 提供全套的強固工具,可協助評估、設計、配置、測試或使用 TI 電池管理產品的程序。其中包括可提供暫存器及資料記憶體完整存取的功能,包括支援即時觀看、繪圖和記錄、傳送命令的簡易介面、直接低階通訊和 I/O,以及用於配置、校準和執行學習週期的自動化和引導支援,進而產生實用的檔案,以利裝置投入生產。

 

bqStudio-web 不支援 bq20xxx、bq30xxx 和 bq40xxx 等較舊的產品。從適當的產品頁面下載特定的評估軟體。此外,您為 bqStudio 下載的最新化學更新程式需要 bqStudio 的更新版。

支援產品和硬體
軟體程式設計工具

BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products

BQ-BATTERY-PROGRAMMER-SW 軟體開發套件 (SDK) 是一系列穩固的軟體命令列工具,可協助使用 TI 電池管理產品進行編程、測試或組裝電池組作業。此軟體中的可執行檔可與 EV2300 通訊收發器的 MKST-3P-ALT-EV2300 MKS 技術替代產品配合使用。這些可執行檔可與單站點一起使用,並可透過使用 MKS Technology Inc. 提供的附加軟體和 GUI 擴展到多個站點。此軟體不支援多工作站。

每次下載都會有多個可執行檔,通常每個平台一個。另外也支援較舊的產品,如 BQ20xxx 和 BQ30xxx。我們提供使用 C++ 程式語言 API 和 (...)

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YAH) 15 Ultra Librarian

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片