首頁 馬達驅動器 電磁線圈驅動器
首頁
馬達驅動器
電磁線圈驅動器
最新

DRV81646-Q1

預覽

車用 70V、3A、四路低壓側馬達驅動器，配備有 PWM/SPI 和可配置電壓轉換速率，CLIM、COD

立即訂購
產品規格表

DRV81646-Q1

預覽
產品規格表 立即訂購

產品詳細資料

Control interface Hardware (GPIO), SPI Control mode PWM Vs (max) (V) 65 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 1.6 Operating temperature range (°C) -40 to 125 Rating Catalog Topology LSS
Control interface Hardware (GPIO), SPI Control mode PWM Vs (max) (V) 65 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 1.6 Operating temperature range (°C) -40 to 125 Rating Catalog Topology LSS
— (—) — See data sheet
  • Four-channel integrated low-side switches
    • 140mΩ RDS(ON) at 25°C
    • Operating supply voltage range: 4.5V to 65V (70V absolute maximum)
    • Selectable current limit from 0.5A up to 4A
    • Fast PWM switching up to 500kHz
  • Flexible interface options:
    • Hardware interface with independent channel PWM input
    • SPI enables reduction in GPIO and isolation overhead for high channel count designs
  • Integrated catch diodes for flexible decay modes with optional external TVS/Zener diode as alternate current path on switch turnoff
  • Slew rate configurable (100ns – 1500ns) enables both slow/fast switching applications
  • Diagnostic feedback
    • MCU fault interrupt signal (nFAULT)
    • Per channel fault report available through SPI
  • Protection Features
    • User settable current limit
    • Independent overtemperature and overcurrent protection for each channel
    • Configurable overcurrent cut-off delay (COD): 0.5ms - 2ms
  • Four-channel integrated low-side switches
    • 140mΩ RDS(ON) at 25°C
    • Operating supply voltage range: 4.5V to 65V (70V absolute maximum)
    • Selectable current limit from 0.5A up to 4A
    • Fast PWM switching up to 500kHz
  • Flexible interface options:
    • Hardware interface with independent channel PWM input
    • SPI enables reduction in GPIO and isolation overhead for high channel count designs
  • Integrated catch diodes for flexible decay modes with optional external TVS/Zener diode as alternate current path on switch turnoff
  • Slew rate configurable (100ns – 1500ns) enables both slow/fast switching applications
  • Diagnostic feedback
    • MCU fault interrupt signal (nFAULT)
    • Per channel fault report available through SPI
  • Protection Features
    • User settable current limit
    • Independent overtemperature and overcurrent protection for each channel
    • Configurable overcurrent cut-off delay (COD): 0.5ms - 2ms

The DRV81646-Q1 is a 4.5V to 65V, four-channel low-side driver with 140mΩ RDS(ON) per switch. An integrated freewheeling diode on each channel connects to the VCLAMP pin, enabling current recirculation or fast inductive load turn-off via an external TVS diode.

Control is available via hardware GPIO or 4-wire SPI. Each channel includes independent overtemperature protection. A single resistor on the ILIM pin globally sets the analog current limit threshold across all channels; an optional cut-off delay (COD) limits overcurrent event duration. Output slew rate is also set globally via the RSLEW/CNTL pin. An INRUSH mode temporarily raises the current limit threshold for capacitive load startup.

An nFAULT output pin indicates fault conditions. In SPI mode, per-channel fault status registers allow rapid fault identification and response.

The DRV81646-Q1 is a 4.5V to 65V, four-channel low-side driver with 140mΩ RDS(ON) per switch. An integrated freewheeling diode on each channel connects to the VCLAMP pin, enabling current recirculation or fast inductive load turn-off via an external TVS diode.

Control is available via hardware GPIO or 4-wire SPI. Each channel includes independent overtemperature protection. A single resistor on the ILIM pin globally sets the analog current limit threshold across all channels; an optional cut-off delay (COD) limits overcurrent event duration. Output slew rate is also set globally via the RSLEW/CNTL pin. An INRUSH mode temporarily raises the current limit threshold for capacitive load startup.

An nFAULT output pin indicates fault conditions. In SPI mode, per-channel fault status registers allow rapid fault identification and response.
filter 尋找其它 電磁線圈驅動器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 DRV81646-Q1 : 65V Four-Channel Low-side Driver with Hardware, SPI, and Configurable Slew Rate and Cut-off Duration datasheet PDF | HTML 2026/5/26

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

DRV81646DGQEVM — DRV81646 評估模組（DGQ 封裝）

DRV81x4x 評估模組 (EVM) 可用於評估 DRV81545、DRV81646 和 DRV81646DGQ 裝置。EVM 已進行程式設計，可立即使用並開始驅動負載。為了簡化控制和配置，EVM 附帶圖形使用者介面 (GUI) 應用程式。
使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
封裝 針腳 CAD 符號、佔位空間與 3D 模型
— (—) —
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片