DRV8303
- 6-V to 60-V Operating Supply Voltage Range
- 1.7-A Source and 2.3-A Sink Gate Drive Current Capability
- Slew Rate Control for EMI Reduction
- Bootstrap Gate Driver With 100% Duty Cycle Support
- 6 or 3 PWM Input Modes
- Dual Integrated Current-Shunt Amplifiers With Adjustable Gain and Offset
- 3.3-V and 5-V Interface Support
- Serial Peripheral Interface (SPI)
- Protection Features:
- Programmable Dead Time Control (DTC)
- Programmable Overcurrent Protection (OCP)
- PVDD and GVDD Undervoltage Lockout (UVLO)
- GVDD Overvoltage Lockout (OVLO)
- Overtemperature Warning/Shutdown (OTW/OTS)
- Reported through nFAULT, nOCTW, and SPI Registers
All trademarks are the property of their respective owners.
The DRV8303 is a gate driver IC for three-phase motor-drive applications. The device provides three half bridge drivers, each capable of driving two N-channel MOSFETs. The device supports up to 1.7-A source and 2.3-A peak current capability. The DRV8303 can operate off of a single power supply with a wide range from 6-V to 60-V. It uses a bootstrap gate-driver architecture with trickle charge circuitry to support 100% duty cycle. The DRV8303 uses automatic hand shaking when the high-side or low-side MOSFET is switching to prevent current shoot through. Integrated VDS sensing of the high-side and low-side MOSFETs is used to protect the external power stage against overcurrent conditions.
The DRV8303 includes two current-shunt amplifiers for accurate current measurement. The amplifiers support bi-directional current sensing and provide and adjustable output offset up to 3 V.
The serial peripheral interface (SPI) provides detailed fault reporting and flexible parameter settings such as gain options for the current-shunt amplifiers and slew-rate control of the gate drivers.
For all available packages, see the orderable addendum at the end of the data sheet.您可能會感興趣的類似產品
功能相似於所比較的產品。
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | DRV8303 Three-Phase Gate Driver With Dual-Current Shunt Amplifiers datasheet (Rev. C) | PDF | HTML | 2016/12/8 | ||
| 應用說明 | Best Practices for Board Layout of Motor Drivers (Rev. B) | PDF | HTML | 2021/10/14 | |||
| 應用說明 | Hardware Design Considerations for an Electric Bicycle using BLDC Motor (Rev. B) | 2021/6/23 | ||||
| 應用說明 | System Design Considerations for High-Power Motor Driver Applications | PDF | HTML | 2021/6/22 | |||
| 白皮書 | Power Electronics in Motor Drives: Where is it? (Rev. A) | 2019/10/1 | ||||
| 應用說明 | Hardware Design Considerations for an Efficient Vacuum Cleaner Using a BLDC Moto (Rev. B) | PDF | HTML | 2019/3/6 | |||
| 技術文章 | What happens when low-voltage BLDC motors drive appliance subsystems | PDF | HTML | 2016/3/17 | |||
| 應用說明 | Sensored 3-Phase BLDC Motor Control Using MSP430 | 2011/7/20 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
BOOSTXL-DRV8301 — 具有 DRV8301 和 NexFET™ MOSFET 的馬達驅動 BoosterPack
The BOOSTXL-DRV8301 is 10A, 3-phase brushless DC drive stage based on the DRV8301 pre-driver and CSD18533Q5A NexFET™ power MOSFET. The module has 3x low side current sense amps (2 internal to DRV8301, 1 external). The module also has a 1.5A step down buck converter, is fully protected with (...)
DRV8303EVM — 適用於具有雙電流分流放大器之三相無刷 DC 預驅動器的 DRV8303 評估模組
The three-phase brushless motor pre-driver DRV8303 can drive brushless DC and brushless AC (BLAC) - often referred to as permanent magnet synchronous (PSMS) - motors with examples of both sensorless Field Oriented / Vector Control (FOC) and TI's InstaSPIN-BLDC sensorless BLDC solution.
The (...)
TIDA-00436 — 堵轉電流限制為 <1us 響應時間的 36V/1kW 無刷 DC 馬達驅動參考設計
本參考設計為適用於額定功率高達 1kW 的電池供電型園林工具和電動工具的無刷馬達功率級，由 10 芯鋰離子電池供電，電壓範圍為 36 至 42V。本設計採用 60V N 通道 NexFETsTM，其汲極至源極電阻 (RDS_ON) 低至 1.8mΩ，封裝採用 SON5x6 SMD，從而實現了 57 × 59mm 的超小 PCB 尺寸。三相位閘極驅動器用於驅動三相位 MOSFET 橋接器，該橋接器的運作電壓範圍為 6 至 60V，並支援可編程閘極電流，最大汲極電流設定為 2.3A/最大源極電流設定為 1.7A。此功率級與 C2000™ Piccolo™ LaunchPad™ (...)
TIDA-00447 — 24V、100W/30W 雙無感測器無刷 DC 馬達驅動參考設計
TIDA-00447 是一款 24V 雙無刷 DC (BLDC) 馬達驅動參考設計，用於在大型家用電器中驅動水泵和風扇等低壓 BLDC 馬達，其用例包括洗碗機的循環泵和排水泵。馬達驅動的功率級分別設計用於 100W 和 30W 的連續運轉。這款 30W 驅動器基於單晶片、低外部元件數量的三相馬達驅動器，整合功率 MOSFET，並提供專有的無感測器控制方案，以提供連續正弦驅動。它還整合了一個降壓/線性穩壓器，可以有效地將供應電壓降至 5V 或 3.3V，為內部和外部電路供電。此 100W 驅動器採用離散式方法實作，包括 MCU、具有保護和電流檢測功能的外部 MOSFET 驅動器和外部功率 (...)
TIDA-00735 — 無刷 DC 推進器控制器參考設計
TIDA-00735 參考設計為 10.8V 至 25.2V 無刷直流馬達控制器，專為高功率螺旋槳、風扇與泵浦應用所設計。採用德州儀器 DRV8303 無刷直流馬達閘極驅動器、CSD17573Q5B 30V NexFET™ 功率 MOSFET、MSP430 16 位元低功率 MCU，以及 TPS70933 30V 超低 IQ LDO。利用梯形無感測器控制演算法控制馬達，並透過來自中央控制器的外部參考訊號調節馬達加速。此設計著重於示範高效率且高功率的 BLDC 馬達系統。
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HTSSOP (DCA) | 48 | Ultra Librarian |