產品詳細資料

Number of full bridges 2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Control mode Independent 1/2-Bridge, PWM Control interface Hardware (GPIO) Features Current Regulation, Current sense Amplifier, Integrated Current Sensing Rating Catalog Operating temperature range (°C) -40 to 125 Topology Push-Pull
Number of full bridges 2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Control mode Independent 1/2-Bridge, PWM Control interface Hardware (GPIO) Features Current Regulation, Current sense Amplifier, Integrated Current Sensing Rating Catalog Operating temperature range (°C) -40 to 125 Topology Push-Pull
HTSSOP (DDV) 44 113.4 mm² 14 x 8.1 HTSSOP (DDW) 44 113.4 mm² 14 x 8.1
  • Four-channel half-bridge driver
    • Independent control of each half-bridge
  • 4.5 V to 65 V operating supply voltage range
  • Low R DS(ON): 50 mΩ for each FET (24 V, 25 °C)
  • High current capacity:
    • DDW package: Up to 5-A per output
    • DDV package: Up to 10-A per output
  • Can drive various types of loads -

    • Up to four solenoids or valves

    • One stepper motor

    • Two brushed-DC motors

    • One or two thermoelectric coolers (TEC)

    • One 3-phase brushless-DC motor

    • One 3-phase permanent magnet synchronous motor (PMSM)

  • Integrated current sense and regulation
    • Current sensing across high-side MOSFETs
    • Sense outputs ( IPROPI) for each half-bridge
    • ± 3.5 % sense accuracy at maximum current
    • Optional external sense resistor

  • Pin-to-pin compatible with:

    • DRV8952: 55 V, four-channel half-bridge driver

  • Separate logic supply voltage ( VCC)
  • Programmable output rise/fall time

  • Programmable fault recovery method

  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Protection features
    • VM undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
  • Four-channel half-bridge driver
    • Independent control of each half-bridge
  • 4.5 V to 65 V operating supply voltage range
  • Low R DS(ON): 50 mΩ for each FET (24 V, 25 °C)
  • High current capacity:
    • DDW package: Up to 5-A per output
    • DDV package: Up to 10-A per output
  • Can drive various types of loads -

    • Up to four solenoids or valves

    • One stepper motor

    • Two brushed-DC motors

    • One or two thermoelectric coolers (TEC)

    • One 3-phase brushless-DC motor

    • One 3-phase permanent magnet synchronous motor (PMSM)

  • Integrated current sense and regulation
    • Current sensing across high-side MOSFETs
    • Sense outputs ( IPROPI) for each half-bridge
    • ± 3.5 % sense accuracy at maximum current
    • Optional external sense resistor

  • Pin-to-pin compatible with:

    • DRV8952: 55 V, four-channel half-bridge driver

  • Separate logic supply voltage ( VCC)
  • Programmable output rise/fall time

  • Programmable fault recovery method

  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Protection features
    • VM undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)

The DRV8962 is a wide-voltage, high-power, four-channel half-bridge driver for a wide variety of industrial applications. The device supports up to 65-V supply voltage, and integrated MOSFETs with 50 mΩ on-resistance allow up to 5-A current on each output with the DDW package; and up to 10-A current per output with the DDV package.

The device can be used for driving up to four solenoids or valves, one stepper motor, two brushed-DC motors, one BLDC or PMSM motor and up to two thermoelectric coolers (Peltier elements). The output stage of the device consists of N-channel power MOSFETs configured as four independent half-bridges, charge pump regulator, current sensing and regulation circuits, current sense outputs and protection circuitry.

Integrated current sensing across the high-side MOSFETs allows the device to regulate the current when the load is connected from output to ground. A regulation current limit can be set with an adjustable external voltage reference (VREF). Additionally, the device provides four proportional current output pins, one for each half-bridge high-side FET. Optional external sense resistors can also be connected from the PGND pins to the system ground.

A low-power sleep mode is provided to achieve ultra- low quiescent current. Internal protection features are provided for supply undervoltage lockout (UVLO), charge pump undervoltage (CPUV), output over current (OCP), and device overtemperature (OTSD).

The DRV8962 is a wide-voltage, high-power, four-channel half-bridge driver for a wide variety of industrial applications. The device supports up to 65-V supply voltage, and integrated MOSFETs with 50 mΩ on-resistance allow up to 5-A current on each output with the DDW package; and up to 10-A current per output with the DDV package.

The device can be used for driving up to four solenoids or valves, one stepper motor, two brushed-DC motors, one BLDC or PMSM motor and up to two thermoelectric coolers (Peltier elements). The output stage of the device consists of N-channel power MOSFETs configured as four independent half-bridges, charge pump regulator, current sensing and regulation circuits, current sense outputs and protection circuitry.

Integrated current sensing across the high-side MOSFETs allows the device to regulate the current when the load is connected from output to ground. A regulation current limit can be set with an adjustable external voltage reference (VREF). Additionally, the device provides four proportional current output pins, one for each half-bridge high-side FET. Optional external sense resistors can also be connected from the PGND pins to the system ground.

A low-power sleep mode is provided to achieve ultra- low quiescent current. Internal protection features are provided for supply undervoltage lockout (UVLO), charge pump undervoltage (CPUV), output over current (OCP), and device overtemperature (OTSD).

下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
可直接投入的替代產品,相較於所比較的裝置,具備升級功能
DRV8952 現行 具電流感測輸出的 50-V 四通道半橋驅動器 Optimized for lower voltage applications (50 V abs max)
功能與所比較的裝置相似
DRV8262 現行 具整合式電流感測和穩壓功能的 65-V 單或雙全橋馬達驅動器 Optimized for brushed motors
DRV8462 現行 具有智慧型微調、熄火偵測和自動扭矩的 65V、10A 雙全橋步進馬達驅動器 Optimized for stepper motors
DRV8844 現行 60V, 2.5A dual H-bridge motor driver, bipolar (+/-30V) supply and independent 1/2-bridge control Optimized for lower current applications
DRV8955 現行 具有電流感測的 50-V、2.5-A、四半橋驅動器 Optimized for lower current and lower voltage applications (50 V abs max)

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 5
類型 標題 日期
* Data sheet DRV8962 Four-channel Half-Bridge Driver with Current Sense Outputs datasheet (Rev. B) PDF | HTML 2023年 9月 28日
Technical article Selecting the right level of integration to meet motor design requirements PDF | HTML 2024年 1月 4日
User guide DRV84xx_DRV82x2_DRV89x2-EVM User's Guide (Rev. B) PDF | HTML 2023年 1月 18日
Certificate DRV8962VEVM EU RoHS Declaration of Conformity (DoC) 2022年 12月 16日
Certificate DRV8962EVM EU RoHS Declaration of Conformity (DoC) 2022年 9月 2日

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

DRV8962EVM — 適用於具電流感測輸出之四路半橋馬達驅動器的 DRV8962 評估模組

DRV8962 EVM 評估模組展示 DRV8962DDWR 的功能和性能。

DRV8962 為四通道半橋式驅動器,每輸出運作範圍為 4.5 V 至 65 V 至 5 A,同時支援各種負載的廣泛負載電流。此裝置整合四個半橋輸出功率級。此裝置也整合電荷泵穩壓器,可支援高效高壓側 N 通道 MOSFET 和 100% 工作週期運作。

此裝置可以從單一電源供應輸入 (VM) 運作。或者、VCC 針腳可連接至第二個電源供應器,提供電源給內建邏輯區塊。

使用指南: PDF | HTML
TI.com 無法提供
開發板

DRV8962VEVM — 適用於採用 DDV 封裝的四路半橋馬達驅動器的 DRV8962 評估模組

DRV8962VEVM 展示了 DRV8962DDVR 的功能和性能。對於此裝置,DDV 封裝的電流能力是 DDW 封裝的兩倍。

DRV8962 為四通道半橋式驅動器,每輸出運作範圍為 4.5V 至 65V 至 10A,同時支援各種負載的廣泛負載電流。此裝置整合四個半橋輸出功率級。此裝置也整合充電幫浦穩壓器,可支援高效高壓側 N 通道 MOSFET 和 100% 工作週期運作。

使用指南: PDF | HTML
TI.com 無法提供
支援軟體

DRV84XX-DRV89X2-DRV82X2-EVM-SOFTWARE EVM GUI and device firmware for DRV84XX_DRV89X2_DRV82X2 family

Zipped folder containing manifests and installers for both the GUI and the firmware of the DRV84XX_DRV89X2_DRV82X2 family of devices. Detailed instructions on how to use the GUI can be found in the User's Guide of the DRV84XX-DRV89X2-DRV82X2-EVM.
支援產品和硬體

支援產品和硬體

產品
有刷 DC (BDC) 馬達驅動器
DRV8952 具電流感測輸出的 50-V 四通道半橋驅動器 DRV8962 具電流感測輸出的 65-V 四通道半橋驅動器 DRV8262 具整合式電流感測和穩壓功能的 65-V 單或雙全橋馬達驅動器
步進馬達驅動器
DRV8462 具有智慧型微調、熄火偵測和自動扭矩的 65V、10A 雙全橋步進馬達驅動器 DRV8452 具智慧型微調、熄火偵測和自動扭矩的 50-V、5-A 雙全橋步進馬達驅動器 DRV8461 具智慧型微調、熄火偵測和自動扭矩的 65-V、3-A 雙全橋步進馬達驅動器
硬體開發
開發板
DRV8462EVM 具自動微步進、適用於步進馬達驅動器的 DRV8462 評估模組 DRV8262EVM 採用 DDW 封裝且適用於單或雙全橋馬達驅動器的 DRV8262 評估模組 DRV8962EVM 適用於具電流感測輸出之四路半橋馬達驅動器的 DRV8962 評估模組 DRV8461EVM 適用 DDW 封裝的 DRV8461 評估模組 DRV8462VEVM 採用 DDV 封裝的步進馬達驅動器 DRV8462 評估模組 DRV8262VEVM 採用 DDV 封裝且適用於單或雙全橋馬達驅動器的 DRV8262 評估模組 DRV8962VEVM 適用於採用 DDV 封裝的四路半橋馬達驅動器的 DRV8962 評估模組
啟動 下載選項
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (DDV) 44 Ultra Librarian
HTSSOP (DDW) 44 Ultra Librarian

訂購與品質

內含資訊:
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊:
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片