首頁 放大器 電流感測放大器 數位電源監測器
首頁
放大器
電流感測放大器
數位電源監測器

INA228-Q1

現行

AEC-Q100、85-V、20 位元、超精密、I²C 輸出電流/電壓/電源/能量/充電監測器

立即訂購
產品規格表

INA228-Q1

現行
產品規格表 立即訂購

產品詳細資料

Common-mode voltage (max) (V) 85 Common-mode voltage (min) (V) -0.3 Digital interface I2C, SMBus Resolution (Bits) 20 Input offset (±) (max) (µV) 1 Input offset drift (±) (max) (µV/°C) 0.01 Input offset drift (±) (typ) (µV/°C) 0.002 Voltage gain (V/V) 1 CMRR (min) (dB) 154 Iq (max) (mA) 1.1 Gain error (%) 0.05 Gain error drift (±) (max) (ppm/°C) 20 Features Alert Function, Bidirectional, Digital Temp Monitor, Integrated Power Accumulator, Integrated Power Monitor, Low-side Capable, Ultra precise Number of channels 1 Power measurement accuracy (%) 0.1 TI functional safety category Functional Safety-Capable Rating Automotive Operating temperature range (°C) -40 to 125
Common-mode voltage (max) (V) 85 Common-mode voltage (min) (V) -0.3 Digital interface I2C, SMBus Resolution (Bits) 20 Input offset (±) (max) (µV) 1 Input offset drift (±) (max) (µV/°C) 0.01 Input offset drift (±) (typ) (µV/°C) 0.002 Voltage gain (V/V) 1 CMRR (min) (dB) 154 Iq (max) (mA) 1.1 Gain error (%) 0.05 Gain error drift (±) (max) (ppm/°C) 20 Features Alert Function, Bidirectional, Digital Temp Monitor, Integrated Power Accumulator, Integrated Power Monitor, Low-side Capable, Ultra precise Number of channels 1 Power measurement accuracy (%) 0.1 TI functional safety category Functional Safety-Capable Rating Automotive Operating temperature range (°C) -40 to 125
VSSOP (DGS) 10 14.7 mm² (3 mm × 4.9 mm)
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • High-resolution, 20-bit delta-sigma ADC
  • Current monitoring accuracy:
    • Offset voltage: ±1 µV (maximum)
    • Offset drift: ±0.01 µV/°C (maximum)
    • Gain error: ±0.05% (maximum)
    • Gain error drift: ±20 ppm/°C (maximum)
    • Common mode rejection: 154 dB (minimum)
  • Power monitoring accuracy:
    • 0.5% full scale, –40°C to +125°C (maximum)
  • Energy and charge accuracy:
    • 1.0% full scale (maximum)
  • Fast alert response: 75 µs
  • Wide common-mode range: –0.3 V to +85 V
  • Bus voltage sense input: 0 V to 85 V
  • Shunt full-scale differential range: ±163.84 mV / ±40.96 mV
  • Input bias current: 2.5 nA (maximum)
  • Temperature sensor: ±1°C (maximum at 25°C)
  • Programmable resistor temperature compensation
  • Programmable conversion time and averaging
  • 2.94-MHz high-speed I2C interface with 16 pin-selectable addresses
  • Operates from a 2.7-V to 5.5-V supply:
    • Operational current: 640 µA (typical)
    • Shutdown current: 5 µA (maximum)
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • High-resolution, 20-bit delta-sigma ADC
  • Current monitoring accuracy:
    • Offset voltage: ±1 µV (maximum)
    • Offset drift: ±0.01 µV/°C (maximum)
    • Gain error: ±0.05% (maximum)
    • Gain error drift: ±20 ppm/°C (maximum)
    • Common mode rejection: 154 dB (minimum)
  • Power monitoring accuracy:
    • 0.5% full scale, –40°C to +125°C (maximum)
  • Energy and charge accuracy:
    • 1.0% full scale (maximum)
  • Fast alert response: 75 µs
  • Wide common-mode range: –0.3 V to +85 V
  • Bus voltage sense input: 0 V to 85 V
  • Shunt full-scale differential range: ±163.84 mV / ±40.96 mV
  • Input bias current: 2.5 nA (maximum)
  • Temperature sensor: ±1°C (maximum at 25°C)
  • Programmable resistor temperature compensation
  • Programmable conversion time and averaging
  • 2.94-MHz high-speed I2C interface with 16 pin-selectable addresses
  • Operates from a 2.7-V to 5.5-V supply:
    • Operational current: 640 µA (typical)
    • Shutdown current: 5 µA (maximum)

The INA228-Q1 is an ultra-precise digital power monitor with a 20-bit delta-sigma ADC specifically designed for current-sensing applications. The device can measure a full-scale differential input of ±163.84 mV or ±40.96 mV across a resistive shunt sense element with common-mode voltage support from –0.3 V to +85 V.

The INA228-Q1 reports current, bus voltage, temperature, power, energy and charge accumulation while employing a precision ±0.5% integrated oscillator, all while performing the needed calculations in the background. The integrated temperature sensor is ±1°C accurate for die temperature measurement and is useful in monitoring the system ambient temperature.

The low offset and gain drift design of the INA228-Q1 allows the device to be used in precise systems that do not undergo multi-temperature calibration during manufacturing. Further, the very low offset voltage and noise allow for use in mA to kA sensing applications and provide a wide dynamic range without significant power dissipation losses on the sensing shunt element. The low input bias current of the device permits the use of larger current-sense resistors, thus providing accurate current measurements in the micro-amp range.

The device allows for selectable ADC conversion times from 50 µs to 4.12 ms as well as sample averaging from 1x to 1024x, which further helps reduce the noise of the measured data.

The INA228-Q1 is an ultra-precise digital power monitor with a 20-bit delta-sigma ADC specifically designed for current-sensing applications. The device can measure a full-scale differential input of ±163.84 mV or ±40.96 mV across a resistive shunt sense element with common-mode voltage support from –0.3 V to +85 V.

The INA228-Q1 reports current, bus voltage, temperature, power, energy and charge accumulation while employing a precision ±0.5% integrated oscillator, all while performing the needed calculations in the background. The integrated temperature sensor is ±1°C accurate for die temperature measurement and is useful in monitoring the system ambient temperature.

The low offset and gain drift design of the INA228-Q1 allows the device to be used in precise systems that do not undergo multi-temperature calibration during manufacturing. Further, the very low offset voltage and noise allow for use in mA to kA sensing applications and provide a wide dynamic range without significant power dissipation losses on the sensing shunt element. The low input bias current of the device permits the use of larger current-sense resistors, thus providing accurate current measurements in the micro-amp range.

The device allows for selectable ADC conversion times from 50 µs to 4.12 ms as well as sample averaging from 1x to 1024x, which further helps reduce the noise of the measured data.
filter 尋找其它 數位電源監測器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
INA238-Q1 現行 AEC-Q100、85-V、16 位元、高精密度、I²C 輸出電流/電壓/充電監測器 Reduced accuracy and reduced functionality for a lower price.
功能相同，但針腳輸出與所比較的裝置不同。
INA229-Q1 現行 AEC-Q100、85-V、20 位元、超精密、SPI 輸出電流/電壓/電源/能量/充電監測器 Same functionality and performance but with a SPI interface.

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 12
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 INA228-Q1 AEC-Q100, 85-V, 20-Bit, Ultra-Precise Power/Energy/Charge Monitor With I2C Interface datasheet (Rev. A) PDF | HTML 2021/6/29
應用說明 Using a PCB Copper Trace as a Current Sense Shunt Resistor (Rev. A) PDF | HTML 2026/4/27
應用說明 Risks and Prevention of ESD, EOS, and Latch Up Events for Current Sense Amplifiers PDF | HTML 2024/11/18
應用說明 Digital Interfaces for Current Sensing Devices (Rev. A) PDF | HTML 2021/9/30
Application brief Integrating the Current Sensing Signal Path (Rev. B) PDF | HTML 2021/9/29
Application brief Integrated, Current Sensing Analog-to-Digital Converter (Rev. A) PDF | HTML 2021/9/28
應用說明 Getting Started with Digital Power Monitors (Rev. A) PDF | HTML 2021/9/2
技術文章 Solving the multidecade current-measurement challenge in your 48-V BMS application PDF | HTML 2021/6/14
Application brief Shunt-Based Current-Sensing Solutions for BMS Applications in HEVs and EVs (Rev. B) PDF | HTML 2021/2/2
功能安全資訊 INA2xx-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA PDF | HTML 2020/11/2
Application brief Energy and Power Monitoring with Digital Current Sensors 2017/5/25
應用說明 Understanding the I2C Bus PDF | HTML 2015/6/30

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

INA228_237_238EVM — INA228、INA237 和 INA238 評估模組

此評估模組 (EVM) 是一款易於使用的平台，可評估 INA228、INA237 或 INA238 的主要功能與性能。

EVM 支援高達 10-A 的電流量測，並隨附圖形使用者介面 (GUI) 支援，可讀取及寫入裝置暫存器。

使用指南: PDF | HTML
支援產品和硬體
IDE、配置、編譯器或偵錯程式

ASC-STUDIO-INA228 — ASC studio (SysConfig) for configuring all aspects of the INA228 current sensor

SysConfig can be used to help simplify configuration challenges and accelerate software development with the INA228 current sensor.
支援產品和硬體
驅動程式或資料庫

INA-WINDOWS-11-E3-DRIVER — 適用於 Windows 11 的能源評估引擎 (E3) 驅動器

Energy Estimation Engine (E3) is a software framework that tracks and attributes power consumption to specific hardware components and software processes. It leverages the EMI (Energy Metering Interface) to report the energy consumption of various power rails.
支援產品和硬體
支援軟體

E3-CONSOLE-APPLICATION-SW — Energy Estimation Engine (E3) driver evaluation software

The E3 Console application uses the Energy Meter Interface (EMI) IOCTLs defined by Microsoft to extract power rail data and measurement. This application can be used to evaluate TI's E3 drivers.
支援產品和硬體
計算工具

ANALOG-ENGINEER-CALC — PC software analog engineer's calculator

類比工程師的計算機旨在加速類比電路設計工程師定期使用的許多重複計算。此基於 PC 的工具提供圖形介面，列出各種常見計算，從使用回饋電阻器設定運算放大器增益到選擇適當的電路設計元件以穩定類比數位轉換器 (ADC) 驅動緩衝電路。

除了作為獨立工具使用外，此計算機還與類比工程師口袋參考中描述的概念相得益彰。

支援產品和硬體
計算工具

CS-AMPLIFIER-ERROR-TOOL — Current Sense Amplifier Comparison and Error Tool

此 Excel 計算機提供兩個與五個標準電流感測放大器的比較，並提供包含各裝置基本參數的圖表。此計算機也會採用使用者的系統條件輸入，例如共模電壓、供應電壓、分流電阻器值與公差，然後在可調整電流範圍中繪製錯誤曲線。此外，計算機會根據計算的全刻度輸入電壓除以最大量測電流，輸出最大分流值 (mΩ)。
支援產品和硬體
計算工具

SBOR021 — Power Monitor Tool

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VSSOP (DGS) 10 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片系列

觀看所有影片

影片