LM4132
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature Range
- Device HBM ESD Classification Level 2
- Output Initial Voltage Accuracy: 0.05%
- Low Temperature Coefficient: 10 ppm/°C
- Low Supply Current: 60 µA
- Enable Pin Allowing a 3-µA Shutdown Mode
- 20-mA Output Current
- Voltage Options: 1.8 V, 2.048 V, 2.5 V, 3 V, 3.3 V, 4.096 V
- Custom Voltage Options Available (1.8 V to 4.096 V)
- VIN Range of VREF + 400 mV to 5.5 V at 10 mA
- Stable With Low-ESR Ceramic Capacitors
The LM4132 family of precision voltage references performs comparable to the best laser-trimmed bipolar references, but in cost-effective CMOS technology. The key to this breakthrough is the use of EEPROM registers for correction of curvature, temperature coefficient (tempco), and accuracy on a CMOS band-gap architecture allowing package-level programming to overcome assembly shift. The shifts in voltage accuracy and tempco during assembly of die into plastic packages limit the accuracy of references trimmed with laser techniques.
Unlike other LDO references, the LM4132 can deliver up to 20 mA and does not require an output capacitor or buffer amplifier. These advantages along with the SOT-23 packaging are important for space-critical applications.
Series references provide lower power consumption than shunt references, because they do not have to idle the maximum possible load current under no-load conditions. This advantage, the low quiescent current (60 µA), and the low dropout voltage (400 mV) make the LM4132 ideal for battery-powered solutions.
The LM4132 is available in five grades (A, B, C, D and E) for greater flexibility. The best grade devices (A) have an initial accuracy of 0.05% with a specified temperature coefficient of 10 ppm/°C or less, while the lowest grade devices (E) have an initial accuracy of 0.5% and a tempco of 30 ppm/°C.
技術文件
| 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | LM4132, LM4132-Q1 SOT-23 Precision Low Dropout Voltage Reference datasheet (Rev. G) | PDF | HTML | 2016年 10月 13日 |
| Application note | Voltage Reference Selection and Design Tips For Data Converters (Rev. B) | PDF | HTML | 2024年 1月 9日 | |
| E-book | Tips and tricks for designing with voltage references (Rev. A) | 2021年 5月 7日 | ||
| E-book | Voltage Supervisor and Reset ICs: Tips, Tricks and Basics | 2019年 6月 28日 | ||
| White paper | Voltage reference selection basics white paper (Rev. A) | 2018年 10月 23日 | ||
| Functional safety information | LM4132, LM4132-Q1 Pin FMEA | 2018年 3月 12日 | ||
| Technical article | Find the 'Goldilocks' voltage reference for your application | PDF | HTML | 2016年 9月 2日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
DIP-ADAPTER-EVM — DIP 轉接器評估模組
Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.
The (...)
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。
在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
TIDEP0025 — 適用於工業通訊和馬達控制的單晶片驅動
TIDA-00574 — Xilinx Zynq 7000 系列 5W 小型高效率低雜訊電源解決方案參考設計
TIDEP0050 — EnDat 2.2 系統參考設計
TIDA-00596 — 適用於伺服器線路卡的小尺寸解決方案多軌參考設計
TIDA-01504 — 配備 HART® 數據機的高準確度、迴路供電、4mA 至 20mA 現場傳送器參考設計
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| SOT-23 (DBV) | 5 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點