首頁 電源管理 DC/DC 切換穩壓器 DC/DC 轉換器
首頁
電源管理
DC/DC 切換穩壓器
DC/DC 轉換器

LM51581-Q1

現行

具備雙隨機展頻的 1.5-A、85-V、2.2-MHz 大範圍 VIN 升壓返馳及 SEPIC 轉換器

立即訂購
產品規格表

LM51581-Q1

現行
產品規格表 立即訂購

產品詳細資料

Rating Automotive Topology Boost, Flyback, SEPIC Vin (max) (V) 60 Vin (min) (V) 1.5 Vout (max) (V) 83 Vout (min) (V) 2 Switch current limit (typ) (A) 1.875 Features Enable, Frequency synchronization, Nonsynchronous rectification, Power good, Spread Spectrum, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Control mode current mode Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.00067 Duty cycle (max) (%) 93 TI functional safety category Functional Safety-Capable
Rating Automotive Topology Boost, Flyback, SEPIC Vin (max) (V) 60 Vin (min) (V) 1.5 Vout (max) (V) 83 Vout (min) (V) 2 Switch current limit (typ) (A) 1.875 Features Enable, Frequency synchronization, Nonsynchronous rectification, Power good, Spread Spectrum, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Control mode current mode Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.00067 Duty cycle (max) (%) 93 TI functional safety category Functional Safety-Capable
WQFN (RTE) 16 9 mm² (3 mm × 3 mm)
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Functional Safety-Capable
  • Suited for wide operating range for car battery applications
    • 3.2-V to 60-V input operating range (65-V abs max)
    • 83-V maximum output (85-V abs max)
    • Minimum boost supply voltage of 1.5 V when BIAS ≥ 3.2 V
    • Input transient protection up to 65 V
    • Minimized battery drain
      • Low shutdown current (IQ ≤ 2.6 µA)
      • Low operating current (IQ ≤ 670 µA)
  • Small solution size and low cost
    • Maximum switching frequency up to 2.2 MHz
    • 16-pin QFN package (3 mm × 3 mm) with wettable flanks
    • Integrated error amplifier allows primary-side regulation without optocoupler (flyback)
    • Minimized undershoot during cranking
    • Accurate current limit (see the Device Comparison Table)
  • EMI mitigation
    • Selectable dual random spread spectrum
    • Lead-less package
  • Higher efficiency with low-power dissipation
    • 133-mΩ RDSON switch
    • Fast switching, small switching loss
  • Avoid AM band interference and crosstalk
    • Optional clock synchronization
    • Dynamically programmable wide switching frequency from 100 kHz to 2.2 MHz
  • Integrated protection features
    • Constant current limiting over input voltage
    • Selectable hiccup mode overload protection
    • Programmable line UVLO
    • OVP protection
    • Thermal shutdown
  • Accurate ±1% accuracy feedback reference
  • Adjustable soft start
  • PGOOD indicator
  • Create a custom design using the LM5158x -Q1 with the WEBENCH Power Designer
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Functional Safety-Capable
  • Suited for wide operating range for car battery applications
    • 3.2-V to 60-V input operating range (65-V abs max)
    • 83-V maximum output (85-V abs max)
    • Minimum boost supply voltage of 1.5 V when BIAS ≥ 3.2 V
    • Input transient protection up to 65 V
    • Minimized battery drain
      • Low shutdown current (IQ ≤ 2.6 µA)
      • Low operating current (IQ ≤ 670 µA)
  • Small solution size and low cost
    • Maximum switching frequency up to 2.2 MHz
    • 16-pin QFN package (3 mm × 3 mm) with wettable flanks
    • Integrated error amplifier allows primary-side regulation without optocoupler (flyback)
    • Minimized undershoot during cranking
    • Accurate current limit (see the Device Comparison Table)
  • EMI mitigation
    • Selectable dual random spread spectrum
    • Lead-less package
  • Higher efficiency with low-power dissipation
    • 133-mΩ RDSON switch
    • Fast switching, small switching loss
  • Avoid AM band interference and crosstalk
    • Optional clock synchronization
    • Dynamically programmable wide switching frequency from 100 kHz to 2.2 MHz
  • Integrated protection features
    • Constant current limiting over input voltage
    • Selectable hiccup mode overload protection
    • Programmable line UVLO
    • OVP protection
    • Thermal shutdown
  • Accurate ±1% accuracy feedback reference
  • Adjustable soft start
  • PGOOD indicator
  • Create a custom design using the LM5158x -Q1 with the WEBENCH Power Designer

The LM5158x -Q1 device is a wide input range, non-synchronous boost converter with an integrated 85-V, 3.26-A (LM5158 -Q1) or 85-V, 1.63-A (LM51581 -Q1) power switch.

The device can be used in boost, SEPIC, and flyback topologies. It can start up from a single-cell battery with a minimum of 3.2 V. It can operate with the input supply voltage as low as 1.5 V if the BIAS pin is greater than 3.2 V.

The BIAS pin operates up to 60 V (65-V absolute maximum) for automotive load dump. The switching frequency is dynamically programmable from 100 kHz to 2.2 MHz with an external resistor. Switching at 2.2 MHz minimizes AM band interference and allows for a small solution size and fast transient response. The device provides a selectable Dual Random Spread Spectrum to help reduce the EMI over a wide frequency range.

The device features an accurate peak current limit over the input voltage, which avoids overdesigning the power inductor. Low operating current and pulse-skipping operation improve efficiency at light loads.

The device has built-in protection features such as overvoltage protection, line UVLO, thermal shutdown, and selectable hiccup mode overload protection. Additional features include low shutdown IQ, programmable soft start, precision reference, a power-good indicator, and external clock synchronization.

The LM5158x -Q1 device is a wide input range, non-synchronous boost converter with an integrated 85-V, 3.26-A (LM5158 -Q1) or 85-V, 1.63-A (LM51581 -Q1) power switch.

The device can be used in boost, SEPIC, and flyback topologies. It can start up from a single-cell battery with a minimum of 3.2 V. It can operate with the input supply voltage as low as 1.5 V if the BIAS pin is greater than 3.2 V.

The BIAS pin operates up to 60 V (65-V absolute maximum) for automotive load dump. The switching frequency is dynamically programmable from 100 kHz to 2.2 MHz with an external resistor. Switching at 2.2 MHz minimizes AM band interference and allows for a small solution size and fast transient response. The device provides a selectable Dual Random Spread Spectrum to help reduce the EMI over a wide frequency range.

The device features an accurate peak current limit over the input voltage, which avoids overdesigning the power inductor. Low operating current and pulse-skipping operation improve efficiency at light loads.

The device has built-in protection features such as overvoltage protection, line UVLO, thermal shutdown, and selectable hiccup mode overload protection. Additional features include low shutdown IQ, programmable soft start, precision reference, a power-good indicator, and external clock synchronization.
filter 尋找其它 DC/DC 轉換器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 9
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 LM5158x-Q1 2.2-MHz Wide VIN 85-V Output Boost/SEPIC/Flyback Converter with Dual Random Spread Spectrum datasheet (Rev. A) PDF | HTML 2021/10/20
應用說明 Reducing Cabling Effort in Camera-Based Driver Monitoring Systems (DMS) PDF | HTML 2023/12/18
白皮書 Isolated Bias Power Supply Architecture for HEV and EV Traction Inverters PDF | HTML 2023/10/11
應用說明 How to Implement the Soft Start in a Flyback PDF | HTML 2023/7/10
應用說明 How to Design an Isolated Flyback Converter Using LM5157x/LM5158x (Rev. A) PDF | HTML 2023/3/16
應用說明 Basic Calculation of a Coupled Inductor SEPIC Power Stage PDF | HTML 2023/3/13
應用說明 How to Design a Boost Converter Using LM5157x, LM5158x PDF | HTML 2021/11/11
功能安全資訊 LM5158x-Q1 Functional Safety FIT Rate, FMD and Pin FMA PDF | HTML 2021/9/20
技術文章 Lowering audible noise in automotive applications with TI’s DRSS technology PDF | HTML 2021/3/18

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LM5157EVM-SEPIC — 適用於 SEPIC 的 LM5157 評估模組

LM5157EVM-SEPIC 評估模組展示了 LM5157 作為寬輸入非同步 SEPIC 轉換器的功能和性能。標準配置的設計可在 4 V 至 32 V 輸入，在 2.1 MHz 下切換時，在最高 1 A 時提供 12 V 的穩壓輸出。

使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

LM5158EVM-BST — LM5158-Q1 升壓轉換器評估模組

LM5158EVM-BST 評估模組展示 LM5158 裝置的功能和性能，此裝置為具備雙隨機展頻的寬輸入電壓升壓轉換器。標準配置的設計可在 3 V 至 9 V 輸入 (輸入電壓 < 6 V 時，負載降低至 0.6 A)、2.1 MHz 切換頻率時，在 1.2 A 時提供 12 V 的穩壓輸出。
使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

LM5158EVM-FLY — LM5158-Q1 返馳式轉換器評估模組

LM5158EVM-FLY 評估模組展示 LM5158 做為返馳式轉換器的功能和性能，可為三相逆變器閘極驅動器偏壓電源的典型應用產生多重輸出電壓軌。  標準配置的設計可在 8V 至 16V 輸入，在 250mA 時提供 10V 的穩壓輸出。另提供三組隔離式 20V 電壓軌，分別提供 75mA、75mA 及 150 mA 電流。   切換頻率為 250kHz。
使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
模擬型號

LM5158x-Q1 Unencrypted PSpice Boost Average (Rev. A)

SNVMC91A.ZIP (39 KB) - PSpice 模型
支援產品和硬體
模擬型號

LM5158x-Q1 Unencrypted PSpice Transient Model (Rev. B)

SNVMC90B.ZIP (163 KB) - PSpice 模型
支援產品和硬體
計算工具

SNVR508 — LM515x Quickstart Calculator for Flyback Regulator Design

支援產品和硬體
計算工具

SNVR511 — LM5157 and LM5158 Quickstart Calculator for Boost Regulator Design

支援產品和硬體
計算工具

SNVR512 — LM5157 and LM5158 Quickstart Calculator for SEPIC Regulator Design

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
WQFN (RTE) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片