首頁 電源管理 LED 驅動器 背光 LED 驅動器
首頁
電源管理
LED 驅動器
背光 LED 驅動器

LP8543

現行

適用中型 LCD 背光的 SMBus/I2C 控制的 WLED 驅動器

立即訂購
產品規格表

LP8543

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 7 Vin (min) (V) 5.5 Vin (max) (V) 22 Vout (min) (V) 10 Vout (max) (V) 40 Type Inductive Switching frequency (max) (kHz) 1250 Duty cycle (max) (%) 100 LED current per channel (mA) 60 Peak efficiency (%) 91 Topology Boost, Current Sink Features Enable/Shutdown, I2C control, PWM control Operating temperature range (°C) -30 to 85 Rating Catalog
Number of channels 7 Vin (min) (V) 5.5 Vin (max) (V) 22 Vout (min) (V) 10 Vout (max) (V) 40 Type Inductive Switching frequency (max) (kHz) 1250 Duty cycle (max) (%) 100 LED current per channel (mA) 60 Peak efficiency (%) 91 Topology Boost, Current Sink Features Enable/Shutdown, I2C control, PWM control Operating temperature range (°C) -30 to 85 Rating Catalog
WQFN (RTW) 24 16 mm² 4 x 4
  • High-Voltage DC/DC Boost Converter with Integrated FET
  • 5.5V to 22V Input Voltage Range to Support 2x, 3x and 4x Li-Ion Batteries.
  • PWM Phase Shift Control with Adaptive Boost Output to Increase Efficiency Compared to Conventional Boost Converters Topologies
  • PWM Brightness Control for Single Wire Control and Stand-Alone Use
  • Digital Ambient Light Sensor Interface with User-Programmed Ambient Light to Backlight Brightness Curve
  • Easy-to-Use EEPROM Calibration for Current, Intensity and Ambient Light Response Setting
  • Seven LED Drivers with LED Fault (Short/open) Detection
  • Eight-Bit LED Current Control
  • Internal Thermal Protection and Backlight Safety Dimming Feature
  • Two Wire, SMBus/ I2C-Compatible Control Interface
  • Low-Input Voltage Detection and Shutdown
  • Minimum Number of External Components
  • WQFN 24-Pin Package, 4 x 4 x 0.8 mm

All trademarks are the property of their respective owners.

  • High-Voltage DC/DC Boost Converter with Integrated FET
  • 5.5V to 22V Input Voltage Range to Support 2x, 3x and 4x Li-Ion Batteries.
  • PWM Phase Shift Control with Adaptive Boost Output to Increase Efficiency Compared to Conventional Boost Converters Topologies
  • PWM Brightness Control for Single Wire Control and Stand-Alone Use
  • Digital Ambient Light Sensor Interface with User-Programmed Ambient Light to Backlight Brightness Curve
  • Easy-to-Use EEPROM Calibration for Current, Intensity and Ambient Light Response Setting
  • Seven LED Drivers with LED Fault (Short/open) Detection
  • Eight-Bit LED Current Control
  • Internal Thermal Protection and Backlight Safety Dimming Feature
  • Two Wire, SMBus/ I2C-Compatible Control Interface
  • Low-Input Voltage Detection and Shutdown
  • Minimum Number of External Components
  • WQFN 24-Pin Package, 4 x 4 x 0.8 mm

All trademarks are the property of their respective owners.

The LP8543 is a white LED driver with integrated boost converter. It has 7 adjustable current sinks which can be controlled by SMBus or I2C-compatible serial interface, PWM input and Ambient Light Sensor (ALS).

The boost converter has adaptive output voltage control based on the LED driver voltages. This feature minimizes the power consumption by adjusting the voltage to lowest sufficient level in all conditions. Phase Shift PWM dimming offers further power saving especially when there is poor matching in the forward voltages of the LED strings. Boost voltage can also be controlled through the SMBus/I2C.

Internal EEPROM stores the data for backlight brightness and ambient light sensor calibration. Brightness can be calibrated during the backlight unit production so that all units produce the same brightness. EEPROM also stores the coefficients for the LED control equations and the default LED current value. LED current has 8–bit adjustment from 0 to 60 mA.

The LP8543 has several safety and diagnostic features. Low-input voltage detection turns the chip off if the system gets stuck and battery fully discharges. Input voltage detection threshold is adjustable for different battery configurations. Thermal regulation reduces backlight brightness above a set temperature. LED fault detection reports open or LED short fault. Boost over-current fault detection protects the chip in case of over-current event.

LP8543 is available in the WQFN 24-pin package.

The LP8543 is a white LED driver with integrated boost converter. It has 7 adjustable current sinks which can be controlled by SMBus or I2C-compatible serial interface, PWM input and Ambient Light Sensor (ALS).

The boost converter has adaptive output voltage control based on the LED driver voltages. This feature minimizes the power consumption by adjusting the voltage to lowest sufficient level in all conditions. Phase Shift PWM dimming offers further power saving especially when there is poor matching in the forward voltages of the LED strings. Boost voltage can also be controlled through the SMBus/I2C.

Internal EEPROM stores the data for backlight brightness and ambient light sensor calibration. Brightness can be calibrated during the backlight unit production so that all units produce the same brightness. EEPROM also stores the coefficients for the LED control equations and the default LED current value. LED current has 8–bit adjustment from 0 to 60 mA.

The LP8543 has several safety and diagnostic features. Low-input voltage detection turns the chip off if the system gets stuck and battery fully discharges. Input voltage detection threshold is adjustable for different battery configurations. Thermal regulation reduces backlight brightness above a set temperature. LED fault detection reports open or LED short fault. Boost over-current fault detection protects the chip in case of over-current event.

LP8543 is available in the WQFN 24-pin package.
open-in-new 尋找其它 背光 LED 驅動器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 3
類型 標題 日期
* Data sheet LP8543 SMBus/I2C Controlled WLED Driver for Medium-Sized LCD Backlight datasheet (Rev. D) 2013年 3月 12日
White paper Common LED Functions and LED Driver Design Considerations 2020年 9月 21日
Selection guide Power Management Guide 2018 (Rev. R) 2018年 6月 25日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 引腳 下載
WQFN (RTW) 24 檢視選項
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 資格摘要
  • 進行中可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片