首頁 交換器與多工器 類比交換器與多工器 通訊協定與匯流排開關與多工器
首頁
交換器與多工器
類比交換器與多工器
通訊協定與匯流排開關與多工器
最新

TMUXHS4446-Q1

預覽

車用 USB-C 10-Gbps 交替模式 6 x 4 多工器/解多工器

立即訂購
產品規格表

TMUXHS4446-Q1

預覽
產品規格表 立即訂購

產品詳細資料

Protocols DisplayPort, USB 3.2 Gen 1x2, USB 3.2 Gen 2x1, USB-C Configuration 4:6 Number of channels 1 USB speed (Mbps) 10000 Bandwidth (MHz) 9500 Ron (typ) (mΩ) 7000 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Supply current (typ) (µA) 350 ESD HBM (typ) (kV) 2 Operating temperature range (°C) -40 to 125 Off isolation (typ) (dB) -60 OFF-state leakage current (max) (µA) 10 Turnoff time (disable) (max) (ns) 650 Turnon time (enable) (max) (ns) 620 Rating Catalog
Protocols DisplayPort, USB 3.2 Gen 1x2, USB 3.2 Gen 2x1, USB-C Configuration 4:6 Number of channels 1 USB speed (Mbps) 10000 Bandwidth (MHz) 9500 Ron (typ) (mΩ) 7000 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Supply current (typ) (µA) 350 ESD HBM (typ) (kV) 2 Operating temperature range (°C) -40 to 125 Off isolation (typ) (dB) -60 OFF-state leakage current (max) (µA) 10 Turnoff time (disable) (max) (ns) 650 Turnon time (enable) (max) (ns) 620 Rating Catalog
WQFN (RET) 40 18 mm² (6 mm × 3 mm)
  • Passive bidirectional USB-C Alternate Mode Mux to switch between USB and DisplayPort signals
  • Supports USB 3.2 up to 10Gbps (Gen 2.0) and DisplayPort 2.1 up to 10Gbps per lane (UHBR10)
  • Compatible for Source/Host and Sink/Device applications
  • −3dB differential BW: 9.5GHz
  • Dynamic characteristics:
    • Insertion loss = −1.6dB at 5GHz
    • Return loss = −18dB at 5GHz
  • Supports common mode voltage (CMV) from 0V to 1.8V
  • Adaptive CMV tracking
  • 6V tolerant SBU pins to survive short-to-VBUS events
  • Can be configured through GPIO pins or I2C
  • Supports both 1.8V and 3.3V I2C
  • Single supply voltage VCC: 3.3V
  • Active power consumption: 340µA
  • Low standby power consumption: 0.5µA (pin mode)
  • Extended Automotive temperature: −40°C to 125°C
  • Available in 3mm × 6mm QFN package
  • Passive bidirectional USB-C Alternate Mode Mux to switch between USB and DisplayPort signals
  • Supports USB 3.2 up to 10Gbps (Gen 2.0) and DisplayPort 2.1 up to 10Gbps per lane (UHBR10)
  • Compatible for Source/Host and Sink/Device applications
  • −3dB differential BW: 9.5GHz
  • Dynamic characteristics:
    • Insertion loss = −1.6dB at 5GHz
    • Return loss = −18dB at 5GHz
  • Supports common mode voltage (CMV) from 0V to 1.8V
  • Adaptive CMV tracking
  • 6V tolerant SBU pins to survive short-to-VBUS events
  • Can be configured through GPIO pins or I2C
  • Supports both 1.8V and 3.3V I2C
  • Single supply voltage VCC: 3.3V
  • Active power consumption: 340µA
  • Low standby power consumption: 0.5µA (pin mode)
  • Extended Automotive temperature: −40°C to 125°C
  • Available in 3mm × 6mm QFN package

The TMUXHS4446-Q1 is a high-speed bidirectional passive crosspoint switch or crossbar (Xbar). This device is used to switch between USB 3.2 Gen2 SuperSpeed and DisplayPort 1.4/2.1 (up to 10Gbps UHBR10) signals over a USB Type-C also known as USB-C interface. The device also provides switching for the low-speed SBU signals that are used for DisplayPort auxiliary channels. The TMUXHS4446-Q1 supports differential signaling with a common mode voltage (CMV) range of 0V to 1.8V and a differential amplitude from 0V to 1800mVpp. Adaptive CMV tracking enables the channel through the device to remain unchanged for the entire common-mode voltage range.

The dynamic characteristics of the TMUXHS4446-Q1 allows high-speed switching with minimum attenuation to the signal eye diagrams, and very little added jitter. The silicon design of the device is optimized for excellent frequency response at a higher frequency spectrum of the signals. The silicon signal traces and switch network of the TMUXHS4446-Q1 are matched for best intra-pair skew performance.

The TMUXHS4446-Q1 has an extended industrial temperature range (−40°C to 125°C) designed for many rugged applications, including industrial and high reliability use cases.

The TMUXHS4446-Q1 is a high-speed bidirectional passive crosspoint switch or crossbar (Xbar). This device is used to switch between USB 3.2 Gen2 SuperSpeed and DisplayPort 1.4/2.1 (up to 10Gbps UHBR10) signals over a USB Type-C also known as USB-C interface. The device also provides switching for the low-speed SBU signals that are used for DisplayPort auxiliary channels. The TMUXHS4446-Q1 supports differential signaling with a common mode voltage (CMV) range of 0V to 1.8V and a differential amplitude from 0V to 1800mVpp. Adaptive CMV tracking enables the channel through the device to remain unchanged for the entire common-mode voltage range.

The dynamic characteristics of the TMUXHS4446-Q1 allows high-speed switching with minimum attenuation to the signal eye diagrams, and very little added jitter. The silicon design of the device is optimized for excellent frequency response at a higher frequency spectrum of the signals. The silicon signal traces and switch network of the TMUXHS4446-Q1 are matched for best intra-pair skew performance.

The TMUXHS4446-Q1 has an extended industrial temperature range (−40°C to 125°C) designed for many rugged applications, including industrial and high reliability use cases.
filter 尋找其它 通訊協定與匯流排開關與多工器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TMUXHS4446-Q1 Automotive rated USB-C 10Gbps Alt Mode Crossbar Mux datasheet PDF | HTML 2026/6/19

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

封裝 針腳 CAD 符號、佔位空間與 3D 模型
WQFN (RET) 40 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片