首頁 電源管理 電源保護開關與控制器 eFuse（整合式熱插拔）
首頁
電源管理
電源保護開關與控制器
eFuse（整合式熱插拔）

TPS25200-Q1

現行

2.5V 至 6.5V、67mΩ、2.1-2.7A 車用 eFuse，關閉時具反向電流阻斷

立即訂購
產品規格表

TPS25200-Q1

現行
產品規格表 立即訂購

產品詳細資料

Vabsmax_cont (V) 20 Vin (max) (V) 6.5 Vin (min) (V) 2.5 Current limit (max) (A) 2.7 Current limit (min) (A) 0.083 Features Fault output, Overcurrent protection, Overvoltage protection, Reverse current blocking when off, Short-circuit protection, Soft-start, Thermal shutdown Overcurrent response Current limiting Fault response Latch-off Ron (typ) (mΩ) 67 Overvoltage response Clamp, Cut-off Rating Automotive Soft start Adjustable Quiescent current (Iq) (typ) (A) 0.000147 Quiescent current (Iq) (max) (A) 0.0002 Device type eFuses and hot swap controllers TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
Vabsmax_cont (V) 20 Vin (max) (V) 6.5 Vin (min) (V) 2.5 Current limit (max) (A) 2.7 Current limit (min) (A) 0.083 Features Fault output, Overcurrent protection, Overvoltage protection, Reverse current blocking when off, Short-circuit protection, Soft-start, Thermal shutdown Overcurrent response Current limiting Fault response Latch-off Ron (typ) (mΩ) 67 Overvoltage response Clamp, Cut-off Rating Automotive Soft start Adjustable Quiescent current (Iq) (typ) (A) 0.000147 Quiescent current (Iq) (max) (A) 0.0002 Device type eFuses and hot swap controllers TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
WSON (DRV) 6 4 mm² 2 x 2
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device HBM Classification Level 2
    • Device CDM Classification Level C5
  • 2.5-V to 6.5-V Operation
  • 20-V Continuous VIN (Absolute Maximum)
  • 7.6-V Input Overvoltage Shutoff
  • 5.25-V to 5.55-V Fixed Overvoltge Clamp
  • 0.6-µs Overvoltage Lockout Response
  • 3.5-µs Short-Circuit Response
  • 67-mΩ High-Side MOSFET
  • Accurate 2.5-A Minimum, 2.9-A Maximum and
    2.1-A Minimum, 2.5-A Maximum Setting (Including
    Resistor)
  • ±6.3% Current-Limit Accuracy at 2.7 A
  • Reverse Current Blocking While Disabled
  • Built-in Soft Start
  • Pin-to-Pin Compatible with TPS2553
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device HBM Classification Level 2
    • Device CDM Classification Level C5
  • 2.5-V to 6.5-V Operation
  • 20-V Continuous VIN (Absolute Maximum)
  • 7.6-V Input Overvoltage Shutoff
  • 5.25-V to 5.55-V Fixed Overvoltge Clamp
  • 0.6-µs Overvoltage Lockout Response
  • 3.5-µs Short-Circuit Response
  • 67-mΩ High-Side MOSFET
  • Accurate 2.5-A Minimum, 2.9-A Maximum and
    2.1-A Minimum, 2.5-A Maximum Setting (Including
    Resistor)
  • ±6.3% Current-Limit Accuracy at 2.7 A
  • Reverse Current Blocking While Disabled
  • Built-in Soft Start
  • Pin-to-Pin Compatible with TPS2553

The TPS25200-Q1 device is a 5-V eFuse with a precision current-limit and overvoltage clamp. The device provides robust protection for load and source during overvoltage and overcurrent events.

The TPS25200-Q1 device is an intelligent protected load-switch with a VIN value tolerant to 20 V. In the event that an incorrect voltage is applied at the IN pin, the output clamps to 5.4 V to protect the load. If the voltage at the IN pin exceeds 7.6 V, the device disconnects the load to prevent damage to the device, load, or both.

The TPS25200-Q1 device has an internal 67-mΩ power switch and is intended for protecting the source, device, and load under a variety of abnormal conditions. The device provides up to 2.4 A of continuous load current. The current-limit is programmable from 85 mA to 2.7 A with a single resistor to ground. During overload events, the output current is limited to the level set by the RILIM resistor. If a persistent overload occurs, the device eventually enters thermal shutoff to prevent damage to the TPS25200-Q1 device.

The TPS25200-Q1 device is a 5-V eFuse with a precision current-limit and overvoltage clamp. The device provides robust protection for load and source during overvoltage and overcurrent events.

The TPS25200-Q1 device is an intelligent protected load-switch with a VIN value tolerant to 20 V. In the event that an incorrect voltage is applied at the IN pin, the output clamps to 5.4 V to protect the load. If the voltage at the IN pin exceeds 7.6 V, the device disconnects the load to prevent damage to the device, load, or both.

The TPS25200-Q1 device has an internal 67-mΩ power switch and is intended for protecting the source, device, and load under a variety of abnormal conditions. The device provides up to 2.4 A of continuous load current. The current-limit is programmable from 85 mA to 2.7 A with a single resistor to ground. During overload events, the output current is limited to the level set by the RILIM resistor. If a persistent overload occurs, the device eventually enters thermal shutoff to prevent damage to the TPS25200-Q1 device.
filter 尋找其它 eFuse（整合式熱插拔）
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 7
類型 標題 日期
* Data sheet TPS25200-Q1 5-V eFuse With Precision Adjustable Current Limit and Overvoltage Clamp datasheet PDF | HTML 2015年 3月 9日
Application note How To Drive Resistive, Inductive, Capacitive, and Lighting Loads (Rev. E) PDF | HTML 2021年 3月 9日
White paper 簡化汽車及工業領域的功 能安全認證 2020年 6月 9日
Functional safety information eFuse: Safety Certification and why it Matters 2020年 3月 18日
Functional safety information TPS25200-Q1 Functional Safety FIT Rate and Failure Mode Distribution 2019年 12月 19日
Application note Basics of eFuses (Rev. A) 2018年 4月 5日
Application note Power Multiplexing Using Load Switches and eFuses (Rev. A) 2017年 6月 20日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS25200EVM-618 — 具有輸入過電壓保護的 TPS25200EVM-618 可調整電流限制配電開關

The TPS25200EVM-618 features an adjustable current limited power distribution switch with input overvoltage protection and output overvoltage clamp. The EVM provides the user with convenient test points, connectors, and various indicators for full evaluation of the TPS25200.

使用指南: PDF
TI.com 無法提供
模擬型號

TPS25200 Unencrypted PSpice Transient Model Package (Rev. A)

SLVMA73A.ZIP (41 KB) - PSpice Model
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
WSON (DRV) 6 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片