首頁 電源管理 電源開關 eFuses 和熱插拔制器
首頁
電源管理
電源開關
eFuses 和熱插拔制器

TPS25947

現行

具有整合式反向極性保護的 2.7V 至 23V、28mΩ、5.5A eFuse

立即訂購
產品規格表

TPS25947

現行
產品規格表 立即訂購

產品詳細資料

FET Internal Ron (typ) (mΩ) 28 Vin (min) (V) 2.7 Vin (max) (V) 23 Vabsmax_cont (V) 28 Current limit (min) (A) 0.5 Current limit (max) (A) 6 Overcurrent response Circuit breaker, current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Clamp, Cut-off Features Current monitoring, Fault output, Power good signal, Reverse current blocking always, Reverse polarity protection UL recognition IEC62368, UL2367 Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
FET Internal Ron (typ) (mΩ) 28 Vin (min) (V) 2.7 Vin (max) (V) 23 Vabsmax_cont (V) 28 Current limit (min) (A) 0.5 Current limit (max) (A) 6 Overcurrent response Circuit breaker, current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Clamp, Cut-off Features Current monitoring, Fault output, Power good signal, Reverse current blocking always, Reverse polarity protection UL recognition IEC62368, UL2367 Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
VQFN-HR (RPW) 10 4 mm² 2 x 2
  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to –15 V
  • Integrated back-to-back FETs with low on-resistance: RON = 28.3 mΩ (typ.)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection
    • Overvoltage clamp (OVC) with pin-selectable threshold (3.8 V, 5.7 V, 13.8 V) and 5-µs (typ.) response time OR
    • Adjustable overvoltage lockout (OVLO) with 1.2-µs (typ.) response time
  • Overcurrent protection with load current monitor output (ILM)
    • Active current limit OR circuit-breaker options
    • Adjustable threshold (ILIM) 0.5 A–6 A
      • ±10% accuracy for ILIM > 1 A
    • Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM
    • Output load current monitor accuracy: ±6% (IOUT ≥ 1 A)
  • Fast-trip response for short-circuit protection
    • 500-ns (typ.) response time
    • Adjustable (2 × ILIM) and fixed thresholds
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Digital outputs
    • Priority power MUX control (AUXOFF) and fault indication (FLT) or
    • Power Good indication (PG) with adjustable threshold (PGTH)
  • UL 2367 recognition
    • File No. E339631
    • RILM ≥ 750 Ω
  • IEC 62368-1 CB certified
  • Small footprint: QFN 2 mm × 2 mm, 0.45-mm pitch
  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to –15 V
  • Integrated back-to-back FETs with low on-resistance: RON = 28.3 mΩ (typ.)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection
    • Overvoltage clamp (OVC) with pin-selectable threshold (3.8 V, 5.7 V, 13.8 V) and 5-µs (typ.) response time OR
    • Adjustable overvoltage lockout (OVLO) with 1.2-µs (typ.) response time
  • Overcurrent protection with load current monitor output (ILM)
    • Active current limit OR circuit-breaker options
    • Adjustable threshold (ILIM) 0.5 A–6 A
      • ±10% accuracy for ILIM > 1 A
    • Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM
    • Output load current monitor accuracy: ±6% (IOUT ≥ 1 A)
  • Fast-trip response for short-circuit protection
    • 500-ns (typ.) response time
    • Adjustable (2 × ILIM) and fixed thresholds
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Digital outputs
    • Priority power MUX control (AUXOFF) and fault indication (FLT) or
    • Power Good indication (PG) with adjustable threshold (PGTH)
  • UL 2367 recognition
    • File No. E339631
    • RILM ≥ 750 Ω
  • IEC 62368-1 CB certified
  • Small footprint: QFN 2 mm × 2 mm, 0.45-mm pitch

The TPS25947xx family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short-circuits, voltage surges, reverse polarity and excessive inrush current. With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the devices well suited for power MUX/ORing applications as well as systems which need load side energy hold up storage in case input power supply fails. The devices use linear ORing based scheme to ensure almost zero DC reverse current and emulate ideal diode behavior with minimum forward voltage drop and power dissipation.

Output slew rate and inrush current can be adjusted using a single external capacitor. Loads are protected from input overvoltage conditions either by clamping the output to a safe fixed maximum voltage (pin selectable), or by cutting off the output if input exceeds an adjustable overvoltage threshold. The devices respond to output overload by actively limiting the current or breaking the circuit. The output current limit threshold as well as the transient overcurrent blanking timer are user adjustable. The current limit control pin also functions as an analog load current monitor.

The devices are available in a 2-mm × 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.

The TPS25947xx family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short-circuits, voltage surges, reverse polarity and excessive inrush current. With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the devices well suited for power MUX/ORing applications as well as systems which need load side energy hold up storage in case input power supply fails. The devices use linear ORing based scheme to ensure almost zero DC reverse current and emulate ideal diode behavior with minimum forward voltage drop and power dissipation.

Output slew rate and inrush current can be adjusted using a single external capacitor. Loads are protected from input overvoltage conditions either by clamping the output to a safe fixed maximum voltage (pin selectable), or by cutting off the output if input exceeds an adjustable overvoltage threshold. The devices respond to output overload by actively limiting the current or breaking the circuit. The output current limit threshold as well as the transient overcurrent blanking timer are user adjustable. The current limit control pin also functions as an analog load current monitor.

The devices are available in a 2-mm × 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.
open-in-new 尋找其它 eFuses 和熱插拔制器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳的功能與所比較的產品相同
TPS25946 現行 具雙向電流支援的 2.7-V 至 23-V、5.5-A、28-mΩ eFuse 2.7-V to 23-V, 5.5A eFuse with bi-directional current support
功能相同，但引腳輸出與所比較的產品不同
最新 TPS25948 現行 具有雙向電力傳輸限制的 3.5-V 至 23-V、12.2-mΩ、8-A eFuse Higher current and lower RON
功能相似於所比較的產品
TPS2521 現行 具有整合式反向極性保護的 2.7-V 至 5.7-V、31-mΩ、4-A eFuse Footprint compatible at reduced voltage and current range.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 10
類型 標題 日期
* Data sheet TPS25947xx, 2.7-V–23-V, 5.5-A, 28-mΩ True Reverse Current Blocking eFuse with Input Reverse Polarity Protection datasheet (Rev. B) PDF | HTML 2022年 3月 25日
Application note How eFuse Ensures Integrated FET Operation in Safe Operating Area PDF | HTML 2022年 9月 7日
Application brief Using an eFuse to Meet IEC62368-3 for USB 2.0 and USB 3.1 Power Sourcing Ports PDF | HTML 2022年 2月 7日
Certificate TPS25947x UL2367 Certificate of Compliance E169910 2022年 1月 19日
Certificate TPS25947x UL2367 Certificate of Compliance E339631 2022年 1月 18日
Certificate TPS25947x CB Test Certificate IEC 62368-1 2021年 12月 8日
Application note Basics of Power MUX (Rev. A) PDF | HTML 2020年 10月 20日
Application brief Fast Role Swap, Linear ORing with TPS25947 and LM73100 in USB-Type C Systems (Rev. A) PDF | HTML 2020年 10月 7日
EVM User's guide TPS25947EVM: Evaluation Module for TPS25947 eFuse 2020年 9月 30日
Application brief eFuses in Smart Electricity Meters PDF | HTML 2020年 9月 1日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS25947EVM — TPS25947 eFuse 評估模組

TPS25947EVM eFuse 評估板允許對 TPS25947 eFuse 產品進行參考電路評估。TPS25947xx 裝置是一款 2.7V 至 5.7V、4-A eFuse，具有整合 28-mΩ FET 和反向電流防護、輸入反極性防護、過電流、突波電流防護、可調式過電流瞬態消隱定時器、可編程欠電壓與過電壓防護。
使用指南: PDF
TI.com 無法提供
模擬型號

TPS25947x PSpice Transient Model (Rev. A)

SLVMDJ6A.ZIP (131 KB) - PSpice Model
下載
計算工具

SLVRBH5 — TPS25947 Design Calculator

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
TPS25947 — 具有整合式反向極性保護的 2.7V 至 23V、28mΩ、5.5A eFuse
下載
計算工具

TVS-RECOMMENDATION-CALC — TVS diode recommendation tool

This tool suggests suitable TVS for given system parameters and abs max voltage rating of the device.
支援產品和硬體

支援產品和硬體

此設計資源支援此類別中多數產品。

檢查產品詳細資料頁面以確認支援。
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
參考設計

TIDA-010239 — AC Level 2 充電器平台參考設計

電動車維修設備 (EVSE) 有助於從電網安全地將電力輸送至電動車。EVSE 控制系統包含輔助功率級、板外 AC/DC 高功率階段 (僅限於 DC 充電站)、能量計量單元、AC 與 DC 殘餘電流偵測器、含驅動程式的隔離監視器單元和繼電器與接觸器、單線雙向通訊，以及服務與使用者介面。此參考設計著重於超低待機隔離式 AC/DC 輔助功率級，接著是轉換器和線性穩壓器、符合 IEC61851 標準的比較器型控制先導介面、高效率繼電器和接觸器驅動、插頭鎖馬達驅動器、用於偵測 RCD 應用的 AC 和 DC 電流的通量閘極電路，以及跨繼電器和接觸器的隔離線路電壓感測。
Design guide: PDF
參考設計

TIDA-010231 — 適合光電應用、適用於電弧偵測的類比前端參考設計

此參考設計在光伏系統中實作四通道類比前端進行 DC 電弧偵測，支援高達 tp 1000 V 的 DC 電壓及高達 10 A 的電流。透過分析太陽能面板和逆變器間 DC 電流的 AC 雜訊，即可偵測電弧。在使用 C2000 即時微控制器 (MCU) 完成頻率分析前，訊號會由條件為類比濾波器階段的電流變壓器擷取，並由 16 位元 ADC ADC8363 取樣。此設計相容於不同 C2000 controlCARD，可將 MCU 調整至系統。可使用 ADS8363 的旁路選項來評估 C2000™ MCU 的內部 ADC。C2000 軟體套件可在最新 (...)
Design guide: PDF
封裝 引腳 下載
VQFN-HR (RPW) 10 檢視選項
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 資格摘要
  • 進行中可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片