TPS92691
- Wide Input Voltage: 4.5 V to 65 V
- Wide Output Voltage Range: 2 V to 65 V
- Low Input Offset Rail-to-Rail Current Sense Amplifier
- Better than ±3% LED Current Accuracy over 25°C to 140°C Junction Temperature Range
- Compatible With High-Side and Low-Side Current Sense Implementations
- High-Impedance Analog LED Current Adjust Input (IADJ) With over 15:1 Contrast Ratio
- Over 1000:1 Series FET PWM Dimming Ratio With Integrated Series N-Channel Dim Driver Interface
- Continuous LED Current Monitor Output for System Fault Detection and Diagnoses
- Programmable Switching Frequency With External Clock Synchronization Capability
- Programmable Soft-Start and Slope Compensation
- Comprehensive Fault Protection Circuitry Including VCC Undervoltage Lockout (UVLO), Output Overvoltage Protection (OVP), Cycle-by-Cycle Switch Current Limit, and Thermal Protection
- TPS92691-Q1: Automotive Q100 Grade 1 Qualified
The TPS92691/-Q1 is a versatile LED controller that can support a range of step-up or step-down driver topologies. The device implements a fixed-frequency peak current mode control technique with programmable switching frequency, slope compensation, and soft-start timing. It incorporates a high voltage (65-V) rail-to-rail current sense amplifier that can directly measure LED current using either a high-side or a low-side series sense resistor. The amplifier is designed to achieve low input offset voltage and attain better than ±3% LED current accuracy over junction temperature range of 25°C to 140°C and output common-mode voltage range of 0 to 60 V.
LED current can be independently modulated using either analog or PWM dimming techniques. Linear analog dimming response with 15:1 range is obtained by varying the voltage from 140 mV to 2.25 V across the high impedance analog adjust (IADJ) input. PWM dimming of LED current is achieved by modulating the PWM input pin with the desired duty cycle and frequency. Optional DDRV gate driver output can be used to enable series FET dimming functionality to get over 1000:1 contrast ratio.
The TPS92691/-Q1 supports continuous LED status check through the current monitor (IMON) output. This allows for LED short circuit or open circuit detection and protection. Additional fault protection features include VCC UVLO, output OVP, switch cycle-by-cycle current limit, and thermal protection.
您可能會感興趣的類似產品
功能相似於所比較的產品。
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | TPS92691/-Q1 Multi-Topology LED Driver With Rail-to-Rail Current Sense Amplifier datasheet | PDF | HTML | 2015/12/11 | ||
| 技術文章 | Driving LEDs: topology matters | PDF | HTML | 2016/2/26 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
TPS92691EVM-001 — TPS92691 SEPIC LED 驅動器評估板
TPS92691EVM-001 是完整組裝且經過測試的 SEPIC LED 驅動器，專為單串串聯 LED 供電。使用相容於高壓側或低壓側電流感測實作的低偏移軌對軌電流感測放大器，即可實現精確的閉合迴路 LED 電流穩壓。 DC LED 電流設定點可利用高阻抗類比調整 (IADJ) 輸入在 15:1 比率上改變。內建整合式閘極驅動器電路與專有 PWM 調光邏輯，可實現高於 100:1 調光比的外部串聯 FET PWM 調光。
LED 短路故障和其他纜線線束故障偵測可由電流監控輸出 (IMON) 協助進行，可報告由軌至軌電流感測放大器測量的 LED 電流瞬時狀態。 (...)
TPS92691EVM-752 — TPS92691-Q1 升壓和升壓至電池 LED 驅動器評估板
TPS92691EVM-752 是完全組裝且經過測試的 LED 驅動器，可配置為升壓或升壓至電池拓撲，為單串列串聯 LED 供電。使用低偏移軌對軌電流感測放大器和高壓側電流感測實作，即可實現精確的閉合迴路 LED 電流穩壓。DC LED 電流設定點可利用高阻抗類比調整 (IADJ) 輸入在 15:1 比率上改變。整合式閘極驅動器電路與專有 PWM 調光邏輯，可實現高於 100:1 調光比的外部串聯 P 通道 MOSFET PWM 調光。
LED 短路故障和其他纜線線束故障偵測可由電流監控器輸出 (IMON) 協助進行，可報告由軌至軌電流感測放大器測量的 LED (...)
SLVC671 — TPS92691 Boost Design Calculator
PMP15003 — 適用於售後市場燈條、聚光燈和泛光燈的可調光 LED 驅動器參考設計
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HTSSOP (PWP) | 16 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。