首頁 電源管理 DC/DC 電源模組 電源模組 (整合式電感器)

TPSM846C26

現行

產品詳細資料

Rating Catalog Topology Buck Iout (max) (A) 35 Vin (max) (V) 18 Vin (min) (V) 2.7 Vout (max) (V) 5.5 Vout (min) (V) 0.4 Features Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Overcurrent protection, PMBus, Phase Interleaving, Power good, Prebias startup, Soft-start adjustable, Stackable, Synchronous rectification, Telemetry, UVLO adjustable, Voltage Margining Operating temperature range (°C) -40 to 125 Type Module Duty cycle (max) (%) 85 Control mode D-CAP4 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000
Rating Catalog Topology Buck Iout (max) (A) 35 Vin (max) (V) 18 Vin (min) (V) 2.7 Vout (max) (V) 5.5 Vout (min) (V) 0.4 Features Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Overcurrent protection, PMBus, Phase Interleaving, Power good, Prebias startup, Soft-start adjustable, Stackable, Synchronous rectification, Telemetry, UVLO adjustable, Voltage Margining Operating temperature range (°C) -40 to 125 Type Module Duty cycle (max) (%) 85 Control mode D-CAP4 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000
FCCSP (APQ) 99 65.625 mm² (7.5 mm × 8.75 mm)
  • Small form factor 7.5mm × 8.75mm BGA package
  • 3.975mm maximum height
  • 2.7V to 18V input voltage with external bias
  • 4V to 18V input voltage without external bias
  • 0.4V to 5.5V output voltage
  • Supports 35A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.6mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pin-strap, additional settings through PMBus®)
  • PMBus programmable
    • Revision 1.5 compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings
  • Two methods for programming the output voltage
    • Internal resistor divider (discrete settings) with boot-up voltage selected by pin-strapping
    • External resistor divider (continuous settings) with boot-up voltage selected by VBOOT
  • Precision voltage reference and differential remote sense for high output accuracy
    • ± 0.5% DAC accuracy from 0°C to 85°C junction
    • ± 0.85% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin-strapping
  • Safe start-up into prebiased output
  • 0.5ms to 16ms programmable soft-start time
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output
  • Small form factor 7.5mm × 8.75mm BGA package
  • 3.975mm maximum height
  • 2.7V to 18V input voltage with external bias
  • 4V to 18V input voltage without external bias
  • 0.4V to 5.5V output voltage
  • Supports 35A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.6mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pin-strap, additional settings through PMBus®)
  • PMBus programmable
    • Revision 1.5 compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings
  • Two methods for programming the output voltage
    • Internal resistor divider (discrete settings) with boot-up voltage selected by pin-strapping
    • External resistor divider (continuous settings) with boot-up voltage selected by VBOOT
  • Precision voltage reference and differential remote sense for high output accuracy
    • ± 0.5% DAC accuracy from 0°C to 85°C junction
    • ± 0.85% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin-strapping
  • Safe start-up into prebiased output
  • 0.5ms to 16ms programmable soft-start time
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output

The TPSM846C26 device is a highly-integrated buck module with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pin-strap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized, digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPSM846C26 devices can be interconnected to provide up to 140A on a single output.

The TPSM846C26 has an option to overdrive the internal 4.5V LDO with an external 5V supply through the VDRV pin to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPSM846C26 is a lead-free device and is RoHS compliant without exemption.

The TPSM846C26 device is a highly-integrated buck module with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pin-strap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized, digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPSM846C26 devices can be interconnected to provide up to 140A on a single output.

The TPSM846C26 has an option to overdrive the internal 4.5V LDO with an external 5V supply through the VDRV pin to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPSM846C26 is a lead-free device and is RoHS compliant without exemption.

下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 4
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TPSM846C26 4V to 18V Input, 35A, 4 × Stackable, Synchronous Buck Module With PMBus and Telemetry datasheet PDF | HTML 2026/10/13
Application brief Higher Power Density With 35A TPSM846C26 Power Module Compared to 35A TPS546C25 DC/DC Converter and Inductor PDF | HTML 2026/11/6
Application brief Powering FPGAs Supporting SmartVID using TI Switching Regulators and Modules With PMBus PDF | HTML 2026/7/21
EVM User's guide TPSM846C26 SWIFT™ Step-Down Converter Evaluation Module PDF | HTML 2026/6/23

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPSM846C26EVM-2PH — TPSM846C26 雙相降壓評估模組

TPSM846C26EVM-2PH 是採用 TPSM846C26 的單相降壓電源模組。TPSM846C26EVM-2PH 專為額定 12V 匯流排而設計,在高達 35A 的負載電流下會產生經調節的 0.8V 輸出。
使用指南: PDF | HTML
支援產品和硬體
設計工具

PMBUS-DESIGN-TOOL — Support PMBus Interface for Buck Converters and Modules

Digital Fusion support for PMBus converters and modules. USB-TO-GPIO2 adapter is needed.
支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
FCCSP (APQ) 99 Ultra Librarian

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片