JAJSRW9 October   2023 BQ25176J

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Device Power Up from Input Source
        1. 7.3.1.1 ISET Pin Detection
        2. 7.3.1.2 VSET Pin Detection
        3. 7.3.1.3 Charger Power Up
      2. 7.3.2 Battery Charging Features
        1. 7.3.2.1 Lithium-Ion Battery Charging Profile
        2. 7.3.2.2 Input Voltage Based Dynamic Power Management (VINDPM)
        3. 7.3.2.3 Charge Termination and Battery Recharge
        4. 7.3.2.4 Charging Safety Timers
        5. 7.3.2.5 Battery Temperature Qualification (TS Pin)
      3. 7.3.3 Status Outputs ( PG, STAT)
        1. 7.3.3.1 Power Good Indicator (PG Pin)
        2. 7.3.3.2 Charging Status Indicator (STAT)
      4. 7.3.4 Protection Features
        1. 7.3.4.1 Input Overvoltage Protection (VIN_OV)
        2. 7.3.4.2 Output Overvoltage Protection (VOUT_OVP)
        3. 7.3.4.3 Output Overcurrent Protection (IOUT_OCP)
        4. 7.3.4.4 Thermal Regulation and Thermal Shutdown (TREG and TSHUT)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Shutdown or Undervoltage Lockout (UVLO)
      2. 7.4.2 Sleep Mode
      3. 7.4.3 Active Mode
        1. 7.4.3.1 Standby Mode
      4. 7.4.4 Fault Mode
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Li-Ion Charger Design Example
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 サード・パーティ製品に関する免責事項
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.1.2 VSET Pin Detection

VSET pin is used to program the device regulation voltage at end-of-charge using a ±1% pulldown resistor. The available pulldown resistor and corresponding charging levels are listed in the following table.

Table 7-1 VSET Pin Resistor Value Table
RESISTOR CHARGE VOLTAGE (V)
> 150 kΩ No charge (open-circuit)
100 kΩ 1-cell LiFePO4: 3.50 V
82.5 kΩ 1-cell LiFePO4: 3.60 V
61.9 kΩ 1-cell LiFePO4: 3.70 V
47.5 kΩ 1-cell Li-Ion: 4.05 V
35.7 kΩ 1-cell Li-Ion: 4.15 V
27.4 kΩ 1-cell Li-Ion: 4.20 V
24.3 kΩ 1-cell Li-Ion: 4.35 V
18.2 kΩ 1-cell Li-Ion: 4.40 V
< 3.0 kΩ No charge (short-circuit)

If either a short- or open-circuit condition is detected, charger stops operation and remains in the FAULT state until the input or TS pin is toggled.

Once a valid resistor value has been detected, the corresponding charge voltage is latched in and the pin is not continuously monitored during operation. A change in this pin will not be acknowledged by the IC until the input supply or TS pin is toggled.