JAJSNC5 april   2023 LM5171-Q1

ADVANCE INFORMATION  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Bias Supplies and Voltage Reference (VCC, VDD, and VREF)
      2. 7.3.2  Undervoltage Lockout (UVLO) and Controller Enable or Disable
      3. 7.3.3  High Voltage Inputs (HV1, HV2)
      4. 7.3.4  Current Sense Amplifier
      5. 7.3.5  Control Commands
        1. 7.3.5.1 Channel Enable Commands (EN1, EN2)
        2. 7.3.5.2 Direction Command (DIR1 and DIR2)
        3. 7.3.5.3 Channel Current Setting Commands (ISET1 and ISET2)
      6. 7.3.6  Channel Current Monitor (IMON1, IMON2)
        1. 7.3.6.1 Individual Channel Current Monitor
        2. 7.3.6.2 Multiphase Total Current Monitoring
      7. 7.3.7  Cycle-by-Cycle Peak Current Limit (IPK)
      8. 7.3.8  Inner Current Loop Error Amplifier
      9. 7.3.9  Outer Voltage Loop Error Amplifier
      10. 7.3.10 Soft Start, Diode Emulation, and Forced PWM Control (SS/DEM1 and SS/DEM2)
        1. 7.3.10.1 Soft-Start Control by the SS/DEM Pins
        2. 7.3.10.2 DEM Programming
        3. 7.3.10.3 FPWM Programming and Dynamic FPWM and DEM Change
        4. 7.3.10.4 SS Pin as the Restart Timer
      11. 7.3.11 Gate Drive Outputs, Dead Time Programming and Adaptive Dead Time (HO1, HO2, LO1, LO2, DT/SD)
      12. 7.3.12 Emergent Latched Shutdown (DT/SD)
      13. 7.3.13 PWM Comparator
      14. 7.3.14 Oscillator (OSC)
      15. 7.3.15 Synchronization to an External Clock (SYNCI, SYNCO)
      16. 7.3.16 Overvoltage Protection (OVP)
      17. 7.3.17 Multiphase Configurations (SYNCO, OPT)
        1. 7.3.17.1 Multiphase in Star Configuration
        2. 7.3.17.2 Daisy-Chain Configurations for 2, 3, or 4 Phases parallel operations
        3. 7.3.17.3 Daisy-Chain configuration for 6 or 8 phases parallel operation
      18. 7.3.18 Thermal Shutdown
    4. 7.4 Programming
      1. 7.4.1 Dynamic Dead Time Adjustment
      2. 7.4.2 UVLO Programming
    5. 7.5 I2C Serial Interface
      1. 7.5.1 REGFIELD Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Small Signal Model
        1. 8.1.1.1 Current Loop Small Signal Model
        2. 8.1.1.2 Current Loop Compensation
        3. 8.1.1.3 Voltage Loop Small Signal Model
        4. 8.1.1.4 Voltage Loop Compensation
    2. 8.2 Typical Application
      1. 8.2.1 60-A, Dual-Phase, 48-V to 12-V Bidirectional Converter
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1  Determining the Duty Cycle
          2. 8.2.1.2.2  Oscillator Programming
          3. 8.2.1.2.3  Power Inductor, RMS and Peak Currents
          4. 8.2.1.2.4  Current Sense (RCS)
          5. 8.2.1.2.5  Current Setting Limits (ISETx)
          6. 8.2.1.2.6  Peak Current Limit
          7. 8.2.1.2.7  Power MOSFETS
          8. 8.2.1.2.8  Bias Supply
          9. 8.2.1.2.9  Boot Strap
          10. 8.2.1.2.10 OVP
          11. 8.2.1.2.11 Dead Time
          12. 8.2.1.2.12 Channel Current Monitor (IMONx)
          13. 8.2.1.2.13 UVLO Pin Usage
          14. 8.2.1.2.14 HVx Pin Configuration
          15. 8.2.1.2.15 Loop Compensation
          16. 8.2.1.2.16 Soft Start
          17. 8.2.1.2.17 PWM to ISET Pins
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 ドキュメントの更新通知を受け取る方法
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  10. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.16 Overvoltage Protection (OVP)

As shown in Figure 7-22, the LM5171-Q1 includes the over voltage protection function, which can be used to monitor either the HV-port, or the LV-port, or a user defined voltage rail, through a resistor divider at the OVP pin.

A resistor divider at the OVP pin sets the OVP threshold. When the OVP pin voltage exceeds the 1.0 V threshold on the rising edge, both HO1 and LO1 are turned off. At the same time CSS1 is discharged, and the CSS1 remains discharged as long as the OVP event lasts. When the OVP voltage falls 105 mV below the 1.0V threshold on the falling edge, the OVP alarm is removed, the SS/DEM1 pulldown is released, and CH-1 resumes operation through a soft-start. See the Soft Start description for details.

Note that OVP alarm only affects CH-1, but not CH-2, and it only protects one voltage rail. Additional OVP functions can be implemented with simple external circuits

  • For multiphase parallel operation, connect SS/DEM1 and SS/DEM2 to enable OVP for both channels as shown in Figure 7-22.
  • For additional voltage rail OVP, employ an external circuit as shown in Figure 7-23, in which an open drain comparator can discharge CSS1 and CSS2 once the protected railed voltage exceeds the OVP threshold.
  • For independent channel operation, an external OVP protection circuit is needed for CH-2 as shown in Figure 7-24, in which CH-1 OVP is implemented with the internal circuit, and the CH-2 OVP is fulfilled by the external open-drain comparator at SS/DEM2. Note the CSS2 also serves as the OVP hiccup mode timer for CH-2.
GUID-20230329-SS0I-PCK2-LVXT-RDKQPQSVX9KV-low.svg Figure 7-22 OVP for CH-1 or Multiphase Parallel Operation
GUID-20230329-SS0I-1W3L-THFN-RJZJSVTJ0WBQ-low.svg Figure 7-23 OVP for 2nd Protected Voltage Rail in Multiphase Parallel Operation
GUID-20220209-SS0I-MCDX-WZ3T-RLVGSF3W6LVW-low.svg Figure 7-24 Independent Channel Operation OVP Implementation