JAJSR90 September   2023 LMQ644A2-Q1

PRODMIX  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Wettable Flanks
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Input Voltage Range (VIN)
      2. 8.3.2  Enable EN Pin and Use as VIN UVLO
      3. 8.3.3  Output Voltage Selection and Soft Start
      4. 8.3.4  SYNC Allows Clock Synchronization and Mode Selection
      5. 8.3.5  Clock Locking
      6. 8.3.6  Adjustable Switching Frequency
      7. 8.3.7  Power-Good Output Voltage Monitoring
      8. 8.3.8  Internal LDO, VCC UVLO, and BIAS Input
      9. 8.3.9  Bootstrap Voltage and VCBOOT-UVLO (CB1 and CB2 Pin)
      10. 8.3.10 CONFIG Device Configuration Pin
      11. 8.3.11 Spread Spectrum
      12. 8.3.12 Soft Start and Recovery From Dropout
      13. 8.3.13 Overcurrent and Short-Circuit Protection
      14. 8.3.14 Hiccup
      15. 8.3.15 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
        1. 8.4.3.1 Peak Current Mode Operation
        2. 8.4.3.2 Auto Mode Operation
          1. 8.4.3.2.1 Diode Emulation
        3. 8.4.3.3 FPWM Mode Operation
        4. 8.4.3.4 Minimum On-time (High Input Voltage) Operation
        5. 8.4.3.5 Dropout
        6. 8.4.3.6 Recovery from Dropout
        7. 8.4.3.7 Other Fault Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1  Choosing the Switching Frequency
        2. 9.2.2.2  Setting the Output Voltage
        3. 9.2.2.3  Inductor Selection
        4. 9.2.2.4  Output Capacitor Selection
        5. 9.2.2.5  Input Capacitor Selection
        6. 9.2.2.6  BOOT Capacitor
        7. 9.2.2.7  VCC
        8. 9.2.2.8  CFF and RFF Selection
        9. 9.2.2.9  SYNCHRONIZATION AND MODE
        10. 9.2.2.10 External UVLO
        11. 9.2.2.11 Typical Thermal Performance
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Ground and Thermal Considerations
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 サード・パーティ製品に関する免責事項
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 用語集
    6. 10.6 静電気放電に関する注意事項
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.1 Absolute Maximum Ratings

Over operating junction temperature range (unless otherwise noted) (1)
MIN MAX UNIT
Pin voltage VIN1, VIN2 to PGND (transient) –0.3 42 V
Pin voltage SW1, SW2 to PGND (less than 10ns transient) –6 42.3 V
Pin voltage SW1, SW2 to PGND (transient) –0.3 42.3 V
Pin voltage BOOT1 - SW1, BOOT2 - SW2 –0.3 5.5 V
Pin voltage EN1, EN2 to AGND –0.3 42 V
Pin voltage PG1, SYNC_OUT/PG2 to AGND –0.3 20 V
Pin voltage SYNC/MODE, FB1, FB2/SS, CONFIG to AGND –0.3 5.5 V
Pin voltage BIAS/VOSNS1, COMP/VOSNS2 to AGND –0.3 22 V
Pin voltage RT, VCC to AGND –0.3 5.5 V
Pin voltage PGND1/2/3 to AGND voltage differential –1 2 V
Sink current PG1, PG2  10 mA
TJ Operating junction temperature –40 150 °C
Tstg Storage temperature –55 150 °C
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.