SPRUJA1 October   2023

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Support Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers
    3. 2.3  Interface Mapping
    4. 2.4  Power ON/OFF Procedure
      1. 2.4.1 Power ON Procedure
      2. 2.4.2 Power OFF Procedure
      3. 2.4.3 Power Test Points
    5. 2.5  Clocking
      1. 2.5.1 Peripheral Ref Clock
    6. 2.6  Reset
    7. 2.7  CSI Interface
    8. 2.8  Audio Codec Interface
    9. 2.9  HDMI Display Interface
    10. 2.10 JTAG Interface
    11. 2.11 Test Automation Header
    12. 2.12 UART Interface
    13. 2.13 USB Interface
      1. 2.13.1 USB 2.0 Type A Interface
      2. 2.13.2 USB 2.0 Type C Interface
    14. 2.14 Memory Interfaces
      1. 2.14.1 OSPI Interface
      2. 2.14.2 MMC Interfaces
        1. 2.14.2.1 MMC0 - eMMC Interface
        2. 2.14.2.2 MMC1 - Micro SD Interface
        3. 2.14.2.3 MMC2 - M.2 Key E Interface
      3. 2.14.3 Board ID EEPROM
    15. 2.15 Ethernet Interface
      1. 2.15.1 CPSW Ethernet PHY 1 Default Configuration
      2. 2.15.2 CPSW Ethernet PHY 2 Default Configuration
    16. 2.16 GPIO Port Expander
    17. 2.17 GPIO Mapping
    18. 2.18 OLDI Display Interface
    19. 2.19 Power
      1. 2.19.1 Power Requirements
      2. 2.19.2 Power Input
      3. 2.19.3 Power Supply
      4. 2.19.4 Power Sequencing
      5. 2.19.5 AM62x SIP SoC Power
      6. 2.19.6 Current Monitoring
    20. 2.20 EVM User Setup/Configuration
      1. 2.20.1 EVM DIP Switches
      2. 2.20.2 Boot Modes
      3. 2.20.3 User Test LEDs
    21. 2.21 Expansion Headers
      1. 2.21.1 PRU Connector
      2. 2.21.2 User Expansion Connector
      3. 2.21.3 MCU Connector
    22. 2.22 Interrupt
    23. 2.23 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 Compliance and Certifications
  10. 5Additional Information
    1. 5.1 Trademarks

2.3 Interface Mapping

Table 2-1 Interface Mapping
Interface Name Port on SoC Device Part Number
Memory – OSPI OSPI0 S28HS512TGABHM010
Memory – Micro SD Socket MMC1 MEM2051-00-195-00-A
Memory – eMMC MMC0 MTFC32GAZAQHD-IT
Memory – Board ID EEPROM SoC_I2C0 AT24C512C-MAHM-T
Ethernet 1 – RGMII SoC_RGMII1 DP83867IRRGZ
Ethernet 2 – RGMII SoC_RGMII2 DP83867IRRGZ
LED Driver – 8 Communication LEDs WKUP_I2C0 TPIC2810D
PRU Header – 2x10 HDR PR0_PRU0_GPO and SoC_I2C0 PREC010DAAN-RC
User Expansion Connector – 2x20 HDR SPI0, SPI2, UART5, SoC_I2C0, SoC_I2C2 and GPIOs PEC20DAAN
MCU Header – 2x14 HDR MCU_UART0,MCU_MCAN0, MCU_SPI0, MCU_I2C0 and MCU GPIOs PREC014DAAN-RC
USB– 2.0 Type C USB0 2012670005
USB– 2.0 Type A USB1 629104151021
LVDS Display Connector OLDI0 FFC2A32-40-T
CSI Interface CSI0 1-1734248-5
HDMI VOUT0 SiI9022ACNU + TPD12S016PWR +10029449-001RLF
AudioCodec McASP2and SoC_I2C1 TLV320AIC3106IRGZT+ SJ-43514-SMT
GPIO Port Expander SoC_I2C1 TCA6424ARGJR
UART Terminal (UART-to-USB) SoC_UART[1:0], WKUP_UART0 and MCU_UART0 FT4232HL+ 629105150521
Test Automation Header SoC_I2C1 FH12A-40S-0.5SH
Temperature Sensor SoC_I2C1 TMP100NA/3K
Current Monitors SoC_I2C1 INA231AIYFDR
Connectivity– M.2 Key E MMC2, McASP1 and SoC_UART1 2199119-4